Makita BO3710 - Инструкция по эксплуатации - Страница 4

4 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model

BO3710

BO3711

Pad size

93 mm x 185 mm

Abrasive paper size

93 mm x 228 mm

Orbits per minute (min

-1

)

11,000

4,000 - 11,000

Overall length

253 mm

Net weight

1.6 kg

Safety class

/II

• 

Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• 

Specifications may differ from country to country.

• 

Weight according to EPTA-Procedure 01/2014

Intended use

The tool is intended for the sanding of large surface of wood, 

plastic and metal materials as well as painted surfaces.

Power supply

The tool should be connected only to a power supply of the 

same voltage as indicated on the nameplate, and can only 

be operated on single-phase AC supply. They are double-in-

sulated in accordance with European Standard and can, 

therefore, also be used from sockets without earth wire.

Noise

The typical A-weighted noise level determined according to EN62841:

Sound pressure level (L

pA

) : 72 dB (A)

Uncertainty (K) : 3 dB (A)

The noise level under working may exceed 80 dB (A).

NOTE:

 The declared noise emission value(s) has been 

measured in accordance with a standard test method 

and may be used for comparing one tool with another.

NOTE:

 The declared noise emission value(s) may 

also be used in a preliminary assessment of exposure.

WARNING:

Wear ear protection.

WARNING:

The noise emission during actual 

use of the power tool can differ from the declared 

value(s) depending on the ways in which the tool is 

used especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures 

to protect the operator that are based on an estima

-

tion of exposure in the actual conditions of use (tak

-

ing account of all parts of the operating cycle such 

as the times when the tool is switched off and when 

it is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN62841:

Work mode : sanding metal plate

Vibration emission (a

h

) : 3.5 m/s

2

Uncertainty (K) : 1.5 m/s

2

NOTE:

 The declared vibration total value(s) has been 

measured in accordance with a standard test method 

and may be used for comparing one tool with another.

NOTE:

 The declared vibration total value(s) may also 

be used in a preliminary assessment of exposure.

WARNING:

The vibration emission during actual 

use of the power tool can differ from the declared val

-

ue(s) depending on the ways in which the tool is used 

especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures 

to protect the operator that are based on an estima

-

tion of exposure in the actual conditions of use (tak

-

ing account of all parts of the operating cycle such 

as the times when the tool is switched off and when 

it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A 

to this instruction manual.

General power tool safety warnings

WARNING:

Read all safety warnings, instruc

-

tions, illustrations and specifications provided with this 

power tool.

 Failure to follow all instructions listed below 

may result in electric shock, fire and/or serious injury.

Save all warnings and instruc

-

tions for future reference.

The term "power tool" in the warnings refers to your mains-oper-

ated (corded) power tool or battery-operated (cordless) power tool.

SANDER SAFETY WARNINGS

1. 

Always use safety glasses or goggles. Ordinary 

eye or sun glasses are NOT safety glasses.

2. 

Hold the tool firmly.

3. 

Do not leave the tool running. Operate the tool 

only when hand-held.

4. 

This tool has not been waterproofed, so do not 

use water on the workpiece surface.

5. 

Ventilate your work area adequately when you 

perform sanding operations.

6. 

Some material contains chemicals which may be 

toxic. Take caution to prevent dust inhalation and 

skin contact. Follow material supplier safety data.