Bosch GSS 23 AE - Инструкция по эксплуатации - Страница 14

14

 | English 

1 609 92A 15N | (18.2.15)

Bosch Power Tools

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate 
of material removal, different sanding sheets are available:

Replacing the Sanding Plate (see figure F)

The sanding plate 

6

 can be replaced, if required.

Unscrew the 4 screws 

11

 completely and remove the sanding 

plate 

6

. Attach the new sanding plate 

6

 and tighten the screws 

again.

Operation

Starting Operation



Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the 
nameplate of the machine. Power tools marked with 
230 V can also be operated with 220 V.

Switching On and Off

To 

start

 the machine, press the On/Off switch 

2

 and keep it 

pressed.

To lock the 

pressed

 On/Off switch 

2

, press the lock-on button 

3

.

To 

switch off

 the machine, release the On/Off switch 

2

 or 

when it is locked with the lock-on button 

3

, briefly press the 

On/Off switch 

2

 and then release it.

To save energy, only switch the power tool on when using it.

Preselecting the Orbital Stroke Rate

With the thumbwheel for preselection of the orbital stroke 
rate 

1

, you can preselect the required orbital stroke rate, even 

during operation.

The required stroke rate depends on the material and the 
working conditions and can be determined through practical 
testing.

Working Advice



Wait until the machine has come to a standstill before 
placing it down. 



Before any work on the machine itself, pull the mains 
plug.

The removal capacity during sanding is mainly determined by 
the selection of the sanding sheet as well as the preselected 
orbital stroke rate.

Only flawless sanding sheets achieve good sanding capacity 
and extend the service life of the machine.

Pay attention to apply uniform sanding pressure; this increas-
es the working life of the sanding sheets.

Intensifiying the sanding pressure does not lead to an in-
crease of the sanding capacity, but to increased wear of the 
machine and the sanding sheet.

A sanding sheet that has been used for metal should not be 
used for other materials.

Use only original Bosch sanding accessories.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself, pull the mains 
plug.



For safe and proper working, always keep the machine 
and ventilation slots clean.

If the replacement of the supply cord is necessary, this has to 
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.

After-sales Service and Application Service

In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of 
the machine.

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange 
the collection of a product in need of servicing or repair. 
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

Grain size

For the working of all wooden 
materials

40 — 240

For coarse-sanding, e. g. of 
rough, unplaned beams and 
boards

coarse

40, 60

For face sanding and planing 
small irregularities

medium 80, 100, 120

For finish and fine sanding of 
hard woods

fine

180, 240

For the working of 
paint/enamel coats or primers 
and fillers

40 — 320

For sanding off paint

coarse

40, 60

For sanding primer

medium 80, 100, 120

For final sanding of primers 
before coating

fine

180, 240, 320

OBJ_BUCH-80-004.book  Page 14  Wednesday, February 18, 2015  1:29 PM