Шлифмашины Bosch GEX 150 AC 0601372768 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
English |
15
Bosch Power Tools
1 609 929 Y19 | (15.3.11)
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
Selection of the Sanding Plate
Depending on the application, the machine can be equipped
with sanding plates of different hardness:
– Soft sanding plate: Suitable for polishing and sensitive
sanding (also for curved surfaces).
– Medium sanding plate: Suitable for all sanding applications
and general-purpose use.
– Hard sanding plate: Suitable for high sanding capacity on
flat surfaces.
Replacing the Sanding Plate (see figure B)
Note:
Replace a damaged sanding plate
8
immediately.
Pull off the sanding sheet or polishing tool. Completely un-
screw the screw
11
and take off the sanding plate
8
. Attach
the new sanding plate
8
and tighten the screw again.
Note:
When attaching the sanding plate, pay attention that
the toothing of the drive element engage into the openings of
the sanding plate.
Dust/Chip Extraction
f
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
f
Prevent dust accumulation at the workplace.
Dusts can
easily ignite.
Material
Application
Grain size
– Paint
– Varnish
– Filling compound
– Filler
For sanding off paint
coarse
40
60
For sanding primer (e. g., for removing brush dashes,
drops of paint and paint run)
medium
80
100
120
For final sanding of primers before coating
fine
180
240
320
400
Expert for Wood
– All wooden materials (e. g.,
hardwood, softwood, chip-
board, building board)
Best for Wood
– Hardwood
– Particle Board
– Building board
– Metal materials
For coarse-sanding, e. g. of rough, unplaned beams and
boards
coarse
40
60
For face sanding and planing small irregularities
medium
80
100
120
For finish and fine sanding of wood
fine
180
240
320
400
– Automotive paint
– Masonry, stone
– Marble
– Granite
– Ceramic
– Glass
– Plexiglas
– Glass-fibre plastics
For pre-sanding
coarse
80
For shaping and braking edges
medium
100
120
For final sanding and forming
fine
180
240
320
400
For polish-sanding and rounding off edges
very fine
600
1 200
OBJ_BUCH-424-004.book Page 15 Tuesday, March 15, 2011 3:24 PM
