Bosch 0.601.795.0R2 - Инструкция по эксплуатации - Страница 16

16

 | English 

1 609 92A 14C | (2.7.15)

Bosch Power Tools

Delivery Scope

Angle grinder, protection guard, auxiliary handle.
Special protection guards, application tools and other acces-
sories shown or described are not part of the standard deliv-
ery scope.

A complete overview of accessories can be found in our ac-
cessories program.

Intended Use

The machine is intended for roughing metal, stone and ceram-
ic materials and for drilling tiles.
For cutting with bonded abrasives, a special cutting guard 
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
Together with the hand guard (accessory), the machine can 
be used for brushing and grinding/sanding with elastic sand-
ing plates.
The machine is suitable only for working without water.

Technical Data

The technical data of the machine are listed in the table on 
page 264 – 266.

The values given are valid for a nominal voltage [U] of 230 V. 
For different voltages and models for specific countries, 
these values can vary.

Please observe the article number on the type plate of your 
machine. The trade names of the individual machines may 
vary.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until 
19 April 2016: 2004/108/EC, from 20 April 2016 on: 
2014/30/EU, 2006/42/EC including their amendments and 
complies with the following standards: EN 60745-1, 
EN 60745-2-3.

Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 02.07.2015

Noise/Vibration Information

The measured values of the machine are listed in the table on 
page 264 – 266.

Sound emission values determined according to 
EN 60745-2-3.

Vibration total values a

h

 (triax vector sum) and uncertainty K 

determined according to EN 60745-2-3.

The vibration level given in this information sheet has been 
measured in accordance with a standardised test given in 
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different 
applications, with different accessories or insertion tools or is 
poorly maintained, the vibration emission may differ. This 
may significantly increase the exposure level over the total 
working period.
An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working 
period.
Identify additional safety measures to protect the operator 
from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work pat-
terns.

Mounting and Operation

The following table indicates the action objectives for mounting and operation of the power tool. The instructions for each action 
objective are shown aside. Depending on the type of application, various instruction combinations are required. Observe the 
safety instructions.

Henk Becker
Executive Vice President
Engineering

Helmut Heinzelmann
Head of Product Certification
PT/ETM9

Action

Figure

Please observe

Page

Grinding, preparation

1

267 – 268

Cutting, preparation

2

269 – 270

30°

OBJ_BUCH-2538-001.book  Page 16  Thursday, July 2, 2015  11:38 AM