Bosch 0.601.795.0R2 - Инструкция по эксплуатации - Страница 13

 English | 

13

Bosch Power Tools

1 609 92A 14C | (2.7.15)



Position the cord clear of the spinning accessory. 

If you 

lose control, the cord may be cut or snagged and your hand 
or arm may be pulled into the spinning wheel.



Never lay the power tool down until the accessory has 
come to a complete stop. 

The spinning wheel may grab 

the surface and pull the power tool out of your control.



Do not run the power tool while carrying it at your side. 

Accidental contact with the spinning accessory could snag 
your clothing, pulling the accessory into your body.



Regularly clean the power tool’s air vents. 

The motor’s 

fan will draw the dust inside the housing and excessive ac-
cumulation of powdered metal may cause electrical haz-
ards.



Do not operate the power tool near flammable materi-
als. 

Sparks could ignite these materials.



Do not use accessories that require liquid coolants. 

Us-

ing water or other liquid coolants may result in electrocu-
tion or shock.

Kickback and related warnings



Kickback is a sudden reaction to a pinched or snagged ro-
tating wheel, backing pad, brush or any other accessory. 
Pinching or snagging causes rapid stalling of the rotating 
accessory which in turn causes the uncontrolled power 
tool to be forced in the direction opposite of the accesso-
ry’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by 
the workpiece, the edge of the wheel that is entering into 
the pinch point can dig into the surface of the material 
causing the wheel to climb out or kick out. The wheel may 
either jump toward or away from the operator, depending 
on direction of the wheel’s movement at the point of pinch-
ing. Abrasive wheels may also break under these condi-
tions.
Kickback is the result of power tool misuse and/or incor-
rect operating procedures or conditions and can be avoid-
ed by taking proper precautions as given below.



Maintain a firm grip on the power tool and position your 
body and arm to allow you to resist kickback forces. Al-
ways use auxiliary handle, if provided, for maximum 
control over kickback or torque reaction during 
start-up. 

The operator can control torque reactions or 

kickback forces, if proper precautions are taken.



Never place your hand near the rotating accessory. 

Ac-

cessory may kickback over your hand.



Do not position your body in the area where power tool 
will move if kickback occurs. 

Kickback will propel the 

tool in direction opposite to the wheel’s movement at the 
point of snagging.



Use special care when working corners, sharp edges, 
etc. Avoid bouncing and snagging the accessory. 

Cor-

ners, sharp edges or bouncing have a tendency to snag the 
rotating accessory and cause loss of control or kickback.



Do not attach a saw chain woodcarving blade or 
toothed saw blade. 

Such blades create frequent kickback 

and loss of control.

Safety warnings specific for Grinding and 
Abrasive Cutting-Off operations



Use only wheel types that are recommended for your 
power tool and the specific guard designed for the se-
lected wheel. 

Wheels for which the power tool was not de-

signed cannot be adequately guarded and are unsafe.



The grinding surface of the centre depressed wheels 
must be mounted below the plane of the guard lip. 

An 

improperly mounted wheel that projects through the plane 
of the guard lip cannot be adequately protected.



The guard must be securely attached to the power tool 
and positioned for maximum safety, so the least 
amount of wheel is exposed towards the operator. 

The 

guard helps to protect operator from broken wheel frag-
ments, accidental contact with wheel and sparks that 
could ignite clothing.



Wheels must be used only for recommended applica-
tions. For example: do not grind with the side of the 
cut-off wheel. 

Abrasive cut-off wheels are intended for 

peripheral grinding; side forces applied to these wheels 
may cause them to shatter.



Always use undamaged wheel flanges that are of cor-
rect size and shape for your selected wheel. 

Proper 

wheel flanges support the wheel thus reducing the possi-
bility of wheel breakage. Flanges for cut-off wheels may be 
different from grinding wheel flanges.



Do not use worn down reinforced wheels from larger 
power tools. 

Wheels intended for larger power tools are 

not suitable for the higher speed of a smaller tool and may 
burst.

Additional safety warnings specific for abrasive 
cutting off operations



Do not “jam” the cut-off wheel or apply excessive pres-
sure. Do not attempt to make an excessive depth of cut. 

Overstressing the wheel increases the loading and suscep-
tibility to twisting or binding of the wheel in the cut and the 
possibility of kickback or wheel breakage.



Do not position your body in line with and behind the 
rotating wheel. 

When the wheel, at the point of operation, 

is moving away from your body, the possible kickback may 
propel the spinning wheel and the power tool directly at 
you. 



When wheel is binding or when interrupting a cut for 
any reason, switch off the power tool and hold the pow-
er tool motionless until the wheel comes to a complete 
stop. Never attempt to remove the cut-off wheel from 
the cut while the wheel is in motion otherwise kickback 
may occur. 

Investigate and take corrective action to elimi-

nate the cause of wheel binding.



Do not restart the cutting operation in the workpiece. 
Let the wheel reach full speed and carefully re-enter 
the cut. 

The wheel may bind, walk up or kickback if the 

power tool is restarted in the workpiece.

OBJ_BUCH-2538-001.book  Page 13  Thursday, July 2, 2015  11:38 AM