Bosch 0.601.795.0R2 - Инструкция по эксплуатации - Страница 12

12

 | English 

1 609 92A 14C | (2.7.15)

Bosch Power Tools



Do not overreach. Keep proper footing and balance at 
all times. 

This enables better control of the power tool in 

unexpected situations.



Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from 
moving parts. 

Loose clothes, jewellery or long hair can be 

caught in moving parts.



If devices are provided for the connection of dust ex-
traction and collection facilities, ensure these are con-
nected and properly used. 

Use of dust collection can re-

duce dust-related hazards.

Power tool use and care



Do not force the power tool. Use the correct power tool 
for your application. 

The correct power tool will do the 

job better and safer at the rate for which it was designed.



Do not use the power tool if the switch does not turn it 
on and off. 

Any power tool that cannot be controlled with 

the switch is dangerous and must be repaired.



Disconnect the plug from the power source and/or the 
battery pack from the power tool before making any 
adjustments, changing accessories, or storing power 
tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.



Store idle power tools out of the reach of children and 
do not allow persons unfamiliar with the power tool or 
these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.



Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other 
condition that may affect the power tool’s operation. If 
damaged, have the power tool repaired before use. 

Many 

accidents are caused by poorly maintained power tools.



Keep cutting tools sharp and clean. 

Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 
and are easier to control.



Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account 
the working conditions and the work to be performed. 

Use of the power tool for operations different from those 
intended could result in a hazardous situation.

Service



Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. 

This will en-

sure that the safety of the power tool is maintained.

Safety Warnings for Angle Grinder

Safety Warnings common for Grinding, Sanding, 
Wire Brushing or Abrasive Cutting Off Operations



This power tool is intended to function as a grinder, 
sander, wire brush or cut-off tool. Read all safety warn-
ings, instructions, illustrations and specifications pro-
vided with this power tool. 

Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or 
serious injury.



Operations such as polishing are not recommended to 
be performed with this power tool. 

Operations for which 

the power tool was not designed may create a hazard and 
cause personal injury.



Do not use accessories which are not specifically de-
signed and recommended by the tool manufacturer. 

Just because the accessory can be attached to your power 
tool, it does not assure safe operation.



The rated speed of the accessory must be at least equal 
to the maximum speed marked on the power tool. 

Ac-

cessories running faster than their rated speed can break 
and fly apart.



The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power 
tool. 

Incorrectly sized accessories cannot be adequately 

guarded or controlled.



Threaded mounting of accessories must match the 
grinder spindle thread. For accessories mounted by 
flanges, the arbour hole of the accessory must fit the 
locating diameter of the flange. 

Accessories that do not 

match the mounting hardware of the power tool will run out 
of balance, vibrate excessively and may cause loss of con-
trol.



Do not use a damaged accessory. Before each use in-
spect the accessory such as abrasive wheels for chips 
and cracks, backing pad for cracks, tear or excess 
wear, wire brush for loose or cracked wires. If power 
tool or accessory is dropped, inspect for damage or in-
stall an undamaged accessory. After inspecting and in-
stalling an accessory, position yourself and bystanders 
away from the plane of the rotating accessory and run 
the power tool at maximum no-load speed for one min-
ute. 

Damaged accessories will normally break apart during 

this test time.



Wear personal protective equipment. Depending on 
application, use face shield, safety goggles or safety 
glasses. As appropriate, wear dust mask, hearing pro-
tectors, gloves and shop apron capable of stopping 
small abrasive or workpiece fragments. 

The eye protec-

tion must be capable of stopping flying debris generated 
by various operations. The dust mask or respirator must be 
capable of filtrating particles generated by your operation. 
Prolonged exposure to high intensity noise may cause 
hearing loss.



Keep bystanders a safe distance away from work area. 
Anyone entering the work area must wear personal 
protective equipment. 

Fragments of workpiece or of a 

broken accessory may fly away and cause injury beyond 
immediate area of operation.



Hold the power tool by insulated gripping surfaces on-
ly, when performing an operation where the cutting ac-
cessory may contact hidden wiring or its own cord. 

Cut-

ting accessory contacting a “live” wire may make exposed 
metal parts of the power tool “live” and could give the op-
erator an electric shock.

OBJ_BUCH-2538-001.book  Page 12  Thursday, July 2, 2015  11:38 AM