Bosch 0.601.795.0R2 - Инструкция по эксплуатации - Страница 14

14

 | English 

1 609 92A 14C | (2.7.15)

Bosch Power Tools



Support panels or any oversized workpiece to minimize 
the risk of wheel pinching and kickback. 

Large work-

pieces tend to sag under their own weight. Supports must 
be placed under the workpiece near the line of cut and near 
the edge of the workpiece on both sides of the wheel.



Use extra caution when making a “pocket cut” into ex-
isting walls or other blind areas. 

The protruding wheel 

may cut gas or water pipes, electrical wiring or objects that 
can cause kickback.

Safety warnings specific for sanding operations



Do not use excessively oversized sanding disc paper. 
Follow manufacturers recommendations, when select-
ing sanding paper. 

Larger sanding paper extending be-

yond the sanding pad presents a laceration hazard and 
may cause snagging, tearing of the disc, or kickback.

Safety warnings specific for wire brushing 
operations



Be aware that wire bristles are thrown by the brush 
even during ordinary operation. Do not overstress the 
wires by applying excessive load to the brush. 

The wire 

bristles can easily penetrate light clothing and/or skin.



If the use of a guard is recommended for wire brushing, 
do not allow any interference of the wire wheel or 
brush with the guard. 

Wire wheel or brush may expand in 

diameter due to work load and centrifugal forces.

Additional Safety and Working 
Instructions



Observe the mains voltage! The voltage of the power 
source must correspond with the data on the type plate 
of the machine.



Use suitable detectors to determine if utility lines are 
hidden in the work area or call the local utility company 
for assistance. 

Contact with electric lines can lead to fire 

and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or 
may cause an electric shock.



Release the On/Off switch and set it to the off position 
when the power supply is interrupted, e. g., in case of a 
power failure or when the mains plug is pulled. 



Dusts from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health and cause allergic reactions, lead to res-
piratory infections and/or cancer.

 Materials containing 

asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable 

for the material.

– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dusts can 

easily ignite.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



After breakage of the grinding disc during operation or 
damage to the holding fixtures on the protection 
guard/power tool, the machine must promptly be sent to 
an after-sales service agent for maintenance. For address-
es, see section “After-sales Service and Application Ser-
vice”.



Adjust protection guard in such a manner that sparking 
toward the operator is prevented.



The protection guard may only be turned while actuat-
ing the release lever on the gear head. Otherwise, the 
machine may not continue to be used anymore and 
must be sent to an after-sales service agent.



Do not touch grinding and cutting discs before they 
have cooled down. 

The discs can become very hot while 

working.



Actuate the spindle lock button only when the grinder 
spindle is at a standstill. 

Otherwise, the machine may be-

come damaged.



After mounting the grinding tool and before switching 
on, check that the grinding tool is correctly mounted 
and that it can turn freely. Make sure that the grinding 
tool does not graze against the protection guard or oth-
er parts.



When operating the machine with power from mobile gen-
erators, loss of performance or untypical behavior can oc-
cur upon switching on.



By applying too high application force, the machine can 
be subject to overload. Overload can lead to overheat-
ing and damage of the power tool. After heavily strain-
ing the power tool, continue to run it at no-load for sev-
eral minutes in order to cool it down.



Do not use the power tool with a cut-off stand.



Never use a cutting disc for roughing.



The quick-clamping nut may be used only for grinding 
or cutting discs. Use only a flawless, undamaged quick-
clamping nut.



Do not pull out the gear head while turning it  –  
see figure 12, page 280.



To save energy, only switch the power tool on when using 
it.



Products sold in GB only:

 Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse 
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should 
be cut off and an appropriate plug fitted in its place by an 
authorised customer service agent. The replacement plug 
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains 
socket elsewhere.

Products sold in AUS and NZ only:

 Use a residual current 

device (RCD) with a rated residual current of 30 mA or 
less.

OBJ_BUCH-2538-001.book  Page 14  Thursday, July 2, 2015  11:38 AM