Bosch AdvancedCut 18 - Инструкция по эксплуатации - Страница 16

16

 | English 

1 609 92A 3Y5 | (25.4.18)

Bosch Power Tools

Inserting the Saw Blade (see figure B)

Use the lever 

9

 to open the cover 

8

 of the SDS saw blade re-

ceptacle. Insert the saw blade as shown in the illustration. En-
sure that the drive shaft and the end of the saw blade fit in the 
recess of the SDS saw blade receptacle 

13

. Close the cover of 

the SDS saw blade receptacle 

8

 and lock it using the locking 

lever of the SDS saw blade receptacle 

9

 until it can be heard 

to engage.

The chain of the saw blade is automatically tensioned.

If the chain slips through or becomes detached from the guide 
unit, open and close the cover of the saw blade receptacle.

Removing the Saw Blade

Open the locking lever 

9

 and fold the cover of the SDS saw 

blade receptacle 

8

 fully upward. Remove the saw blade.

Dust/Chip Extraction



Dust from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health. Touching or breathing-in the dust can cause 
allergic reactions and/or lead to respiratory infections of 
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment 
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dust can 

easily ignite.

Operation



Never bend the saw blade!

Starting Operation

Inserting the battery
Note: 

Use of batteries not suitable for the machine can lead to 

malfunctions of or cause damage to the power tool.

Insert the charged battery 

6

 into the handle until it can be felt 

to engage and faces flush against the handle.

Switching On and Off

To 

switch on

 the power tool, 

first

 press the lock-off button 

3

right or left. 

Then

 press the On/Off switch 

4

 and keep it pressed.

You can let go of the lock-off button 

3

 while the tool is 

switched on.

To 

switch off

 the power tool, release the On/Off switch 

4

.

To save energy, only switch the power tool on when using it.

The lithium-ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the power tool is switched off by means of a protective 
circuit: The inserted tool no longer moves.



Do not continue to press the On/Off switch after the 
machine has been automatically switched off. 

The bat-

tery can be damaged.

Controlling the Sawing Speed

The sawing speed of the switched-on power tool can be varia-
bly adjusted, depending on how far the On/Off switch 

4

 is 

pressed. 

The required sawing speed is dependent on the material and 
the work conditions and can be determined by practical trials.

It is recommended that you reduce the sawing speed when 
putting the saw blade on the workpiece.

Battery Charge-control Indication

The battery charge-control indicator 

7

 displays the charge 

condition of the battery for several seconds when the On/Off 
switch 

4

 is half-pressed or fully pressed; it consists of an LED 

with two colours.

Working Advice (see figures C – G)



When sawing small or thin workpieces, always use a 
firm support.



When sawing, ensure that the cutting direction is from 
the front backwards (see figure E) or from the top 
downwards (see figure C)!



Do not carry the power tool on your wrist! 

The suspen-

sion strap is intended only for storage.

The riving knife 

10

 prevents sawing against the running direc-

tion of the chain saw.

Saw with moderate pressure in order to achieve optimal and 
precise cutting results. Applying additional pressure increases 
performance.

If the saw blade should jam, switch the machine off immedi-
ately. Widen the gap somewhat with a suitable tool and pull 
out the machine.

Temperature-dependent Overload Protection

In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is placed under too much pressure or 
the permitted battery temperature range is left, the tool 
switches off. Following an automatic shut-off, switch off the 
power tool, allow the battery to cool and then switch the pow-
er tool back on.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Store the battery only within a temperature range between 
– 20 ° C and 50 ° C. As an example, do not leave the battery in 
the car in summer.

A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.

Observe the notes for disposal.

LED

Capacity

Continuous lighting, green 

≥30 %

Continuous lighting, red

<30 %

Flashing light, red *

0 %

* The battery charge-control indicator also flashes red when the battery 
overheats or is overloaded.

OBJ_BUCH-3326-001.book  Page 16  Wednesday, April 25, 2018  2:48 PM