ROWENTA RR7375WH - Инструкция по эксплуатации - Страница 33

64

65

5.

IS THERE A PROBLEM WITH YOUR APPLIANCE?

According to model:

•  

The charger is getting hot:

4

  This is perfectly normal. The vacuum cleaner can remain permanently connected to the charger 

without any risk.

• The charger is connected but your appliance is not charging:

  - The charger is incorrectly attached to the appliance or is faulty.

4

  Check that the charger is properly connected or contact an Approved Services Centre to change 

the charger.

• Your appliance stops during use:

  - Your appliance may be overheating.

4

  Stop the appliance and leave cool for at least 1 hour.

4

  If it overheats on repeated occasions, contact the Approved Services Centre.

• The appliance stopped after the charge light was flashing:

  - The appliance has run out of battery charge.

4

  Recharge the vacuum cleaner.

• The power-brush is not working properly or makes a noise:

  - The rotating brush or hose are obstructed.

4

  Stop the vacuum cleaner and clean them.

  - The brush is worn.

4

  Contact an Approved Service Centre to change the brush.

  - The belt is worn.

4

  Contact an Approved Service Centre to change the belt.

• The power-brush stops during vacuuming:

  - The safety function has been triggered.

4

  Stop the vacuum cleaner. Check that nothing is obstructing the rotation of the brush; if there is an 

obstruction, remove it and clean the power-brush, then turn on the vacuum cleaner.

• Your vacuum cleaner is not vacuuming as well, is making noise, whistling:

  - The intake channel is partially blocked.

4

  Unblock it

  - The dust collector is full.



Empty it and clean it.

  - The dust collector is not properly fitted.

4

  Re-position it correctly.

  - The intake head is clogged.

4

  Remove the power-brush and clean it.

  - The protective foam filter is saturated.

4

  Clean it. 

EN

RR73XX
Error 

Indicator Light

Error 

Designations

Error Forms 

Solutions

The red indicator light 

blinks twice and beeps

Failure of the left wheel

The left wheel does not 

turn and is overloaded.

Please confirm that the 

device's left wheel is not 

covered.

The red indicator light 

blinks three times and 

beeps

Failure of the right wheel

The right wheel does 

not turn and is over-

loaded

Please confirm that the 

device's right wheel is not 

covered.

The red indicator light

blinks four times and 

beeps 

Failure of robot lifted 

The robot is lifted over 1 

second.

Please clean your vacuum 

sensors and put your robot 

back on the ground.

The red indicator light 

blinks five times and 

beeps

Failure of the front wheel

The front wheel is blocked 

and no longer turns.

Please confirm that the 

small wheels of the front 

wheel are not covered.

The red indicator light 

blinks six times and 

beeps

Failure of the ground 

inspection

There is a problem with 

the ground inspection.

Please confirm that the sen-

sor window at the bottom 

of the device is not unusu-

ally concealed.

The red indicator light 

blinks seven times and 

beeps

Low current or battery

The battery power sup-

ply was extremely low 

(but not at the recharge 

voltage critical point).

Please replace the device 

on the docking station to 

recharge it.

The red indicator light 

blinks eight times and 

beeps

Failure of the front 

bumper

The impact switches 

on the front left and 

right shells cannot be 

restored.

Please check whether or not 

the device's stop is normal.

The red indicator light 

blinks nine times and 

beeps

Failure of the main brush

The wheel of the main 

brush is overloaded or 

insufficiently charged.

Please confirm that no for-

eign bodies are present on 

the device's main brush.

The red indicator light 

blinks ten times and 

beeps

Failure of the side brush

The side sweeper wheel 

is overloaded or insuffi-

ciently charged.

Please confirm that ele-

ments such as hair or fabric 

are not wound around the 

side brush.

The red indicator light 

blinks eleven times and 

beeps

Failure of the wall in-

spection

There is a problem with 

the wall inspection.

Please confirm that the wall 

inspection clear window is 

not concealed or obstructed 

by hair or fabric.

The red indicator light 

blinks twelve times and 

beeps

Failure of the fan

The fan only turns with 

significant current flow.

Please confirm that the 

fan blades are not loose or 

jammed by hair or fabric.

The red indicator light 

blinks fourteen times 

and beeps

Load failure

The device cannot be 

supplied with power 

or cannot indicate the 

charge status.

Please confirm that the 

device is connected to the 

docking station.

Please keep this user manual.

5.