Ryobi RMT18-0 - Инструкция по эксплуатации - Страница 3

Safety, performance, and dependability have been given 
top priority in the design of your multi tool.

INTENDED USE

The multi tool is intended to be used only by adults who 
have read and understood the instructions and warnings 
in this manual and can be considered responsible for their 
actions. 
The multi tool is intended to be used:

–

for sanding and finishing metal, wood, plastics, or 
similar materials using the sanding pad with the 
shaped abrasive sheets provided

–

for scraping and plunge-cutting into non-ferrous 
metal, wood, plastics, plasterboard, etc. using the 
provided metallic cutting blades

–

for cutting holes in walls to accommodate switches 
or power sockets

–

for removing grouting from between ceramic tiles

The multi tool is intended to be operated indoors in dry, well-
illuminated, and adequately ventilated conditions.
The multi tool is not intended to be used on wet materials 
or surfaces.
Do not use the product in any way other than those stated 
for intended use.

WARNING!

Read all safety warnings, instructions, 

illustrations and specifications provided with this 
power tool.

 Failure to follow all instructions listed below 

may result in electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

MULTI TOOL SAFETY WARNINGS

■

Hold the power tool by insulated gripping surfaces, 
when performing an operation where the cutting 
accessory may contact hidden wiring. 

Cutting 

accessory contacting a “live” wire may make exposed 

metal parts of the power tool “live” and could give the 

operator an electric shock.

■

Always wear safety goggles and a dust mask when 

sanding, especially sanding overhead.

■

A suitable breathing respirator must be worn while 

sanding lead paint, some woods, and metal to avoid 

breathing the harmful/toxic dust or air.

■

The dust produced when using the product may be 

harmful to the health of the operator and bystanders. 

Operator and bystanders shall not touch and not inhale 

the dust. Wear a suitable dust protection mask.

■

Do not machine any materials that present a danger to 

health, such as asbestos.

■

Clamp the workpiece with a clamping device. Unclamped 

workpieces can cause severe injury and damage.

■

Switch the product off immediately if the accessory 
stalls. Do not switch the product on again while the 
accessory is stalled, as doing so could trigger a sudden 
recoil with a high reactive force. Determine why the 
accessory stalled and rectify this, paying heed to the 
safety instructions.

■

Ambient temperature range for tool during operation is 
between 

0

°C and 

40

°C.

■

Ambient temperature range for tool storage is between 

0

°C and 

40

°C.

■

The recommended ambient temperature range for the 
charging system during charging is between 

10

°C and 

38

°C.

ADDITIONAL BATTERY SAFETY WARNINGS

■

To reduce the risk of fire, personal injury, and product 
damage due to a short circuit, never immerse your 
tool, battery pack, or charger in fluid or allow fluid to 
flow inside them. Corrosive or conductive fluids, such 
as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

■

Ambient temperature range for battery during use is 
between 

0

°C and 

40

°C.

■

Ambient temperature range for battery storage is 
between 

0

°C and 

20

°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.
Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps or 
tape. Do not transport batteries that are cracked or leaking. 
Check with the forwarding company for further advice.

KNOW YOUR PRODUCT

See page 57.

1. LED light
2.  Blade locking screw
3. Speed control
4.  Lock on switch
5. On/off switch
6.  Handle, insulated grasping surface
7. Battery port
8. Hex key
9.  Plunge cut blade
10. Flush cut blade
11. Adaptor */**
12. Sandpaper
13. Sanding pad
14. Operator’s manual
15. Battery pack
16. Charger
*Compatible with BOSCH accessories. BOSCH is a 
registered trademark of Robert Bosch GmbH.
**Compatible with DREMEL accessories. DREMEL is a 
registered trademark of Robert Bosch Tool Corporation.

MAINTENANCE

■

The product should never be connected to a power 
supply when assembling parts, making adjustments, 
cleaning, performing maintenance, or when the product 
is not in use. Disconnecting the product from the power 
supply will prevent accidental starting that could cause 
serious injury.

■

When servicing, use only original manufacturer’s 
replacement parts, accessories and attachments. Use 
of any other parts may create a hazard or cause product 
damage.

■

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to various types of commercial 
solvents and may be damaged by their use. Use clean 
cloths to remove dirt, carbon dust, etc.

■

Do not at any time let brake fluids, gasoline, petroleum-

ENGLISH

EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL

3

Original Instructions