Ryobi R18MMS-0 (5133004515) - Инструкция по эксплуатации - Страница 5

3

 English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL

Kickback is the result of power tool misuse and/or incorrect 
operating procedures or conditions and can be avoided by 
taking proper precautions as given below.

■

Maintain a firm grip on the power tool and position 
your body and arm to allow you to resist kickback 
forces. Always use auxiliary handle, if provided, for 
maximum control over kickback or torque reaction 
during start-up.

 The operator can control torque 

reactions or kickback forces, if proper precautions are 
taken.

■

Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

■

Do not position your body in line with the rotating 
wheel.

 Kickback will propel the tool in direction opposite 

to the wheel’s movement at the point of snagging.

■

Use special care when working corners, sharp 
edges etc. Avoid bouncing and snagging the 
accessory.

 Corners, sharp edges or bouncing have a 

tendency to snag the rotating accessory and cause loss 
of control or kickback.

■

Do not attach a saw chain, woodcarving blade, 
segmented diamond wheel with a peripheral gap 
greater than 10 mm or toothed saw blade.

 Such 

blades create frequent kickback and loss of control.

■

Do not “jam” the wheel or apply excessive pressure. 
Do not attempt to make an excessive depth of cut.

Overstressing the wheel increases the loading and 
susceptibility to twisting or binding of the wheel in the 
cut and the possibility of kickback or wheel breakage.

■

When wheel is binding or when interrupting a cut 
for any reason, switch off the power tool and hold 
the power tool motionless until the wheel comes to 
a complete stop. Never attempt to remove the wheel 
from the cut while the wheel is in motion otherwise 
kickback may occur.

 Investigate and take corrective 

action to eliminate the cause of wheel binding.

■

Do not restart the cutting operation in the workpiece. 
Let the wheel reach full speed and carefully re-enter 
the cut.

 The wheel may bind, walk up or kickback if the 

power tool is restarted in the workpiece.

■

Support panels or any oversized workpiece to 
minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight. 
Supports must be placed under the workpiece near the 
line of cut and near the edge of the workpiece on both 
sides of the wheel.

■

Use extra caution when making a “pocket cut” into 
existing walls or other blind areas.

 The protruding 

wheel may cut gas or water pipes, electrical wiring or 
objects that can cause kickback.

■

Use slow steady pressure when cutting tile. 

Do not 

force the product.

 Use of excessive pressure may 

damage the motor.

■

Cutting tile for extended periods of time or cutting tile 
longer than 30 cm could cause the saw to become 
overheated. If this occurs, cool the saw by retracting 
the wheel/blade into the guard, lifting the saw away 
from the workpiece, and running the saw at full speed 
for two minutes.

ADDITIONAL SAFETY WARNINGS

■

Do not use any abrasive wheels.

■

Use only blade diameter(s) in accordance with the 
markings.

■

Identify the correct saw blade to be used for the material 
to be cut.

■

Use only saw blades that are marked with a speed 
equal or higher than the speed marked on the tool.

■

Use only saw blades recommended by the 
manufacturer, which conform to EN 847-1, if intended 
for wood and analogous materials.

■

Wear a dust mask.

■

Use the dust collection device or connect a dust 
extraction vacuum when operating the product. Do not 
use a dust extraction vacuum when cutting metal.

■

Avoid overheating the blade tips and melting the plastic.

■

Check and ensure that the blade guard can move only 
when the lock-off button is pressed, and that it will 
return to its original position when released.

■

The product will restart automatically if stalled. Switch 
off the product immediately if it stalls. Do not switch on 
the product again while it is still stalled, as doing so 
could trigger a sudden recoil with a high reactive force. 
Determine why the product stalled and rectify this, 
paying heed to the safety instructions.

■

Ambient temperature range for tool during operation is 
between 0°C and 40°C.

■

Ambient temperature range for tool storage is between 
0°C and 40°C.

■

The recommended ambient temperature range for the 
charging system during charging is between 10°C and 
38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

 WARNING

To reduce the risk of 

fi

 re, personal injury, and product 

damage due to a short circuit, never immerse your 
tool, battery pack or charger in 

fl

 uid or allow a 

fl

 uid  to 

fl

 ow inside them. Corrosive or conductive 

fl

 uids,  such 

as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

■

Ambient temperature range for battery during use is 
between 0°C and 40°C.

■

Ambient temperature range for battery storage is 
between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.
Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps 
or tape. Do not transport batteries that are cracked or