Makita M5802 - Инструкция по эксплуатации - Страница 7

7 ENGLISH

damaged parts, gummy deposits, or a build-up of 

debris.

3. 

Lower guard may be retracted manually only 

for special cuts such as “plunge cuts” and 

“compound cuts”. Raise lower guard by 

retracting handle and as soon as blade enters 

the material, the lower guard must be released.

For all other sawing, the lower guard should oper-

ate automatically.

4. 

Always observe that the lower guard is cov-

ering the blade before placing saw down on 

bench or floor.

 An unprotected, coasting blade 

will cause the saw to walk backwards, cutting 

whatever is in its path. Be aware of the time it 

takes for the blade to stop after switch is released.

5. 

To check lower guard, open lower guard by 

hand, then release and watch guard closure. 

Also check to see that retracting handle does 

not touch tool housing.

 Leaving blade exposed 

is VERY DANGEROUS and can lead to serious 

personal injury.

Additional safety warnings

1. 

Use extra caution when cutting damp wood, pres-

sure treated lumber, or wood containing knots.

Maintain smooth advancement of tool without decrease 

in blade speed to avoid overheating the blade tips.

2. 

Do not attempt to remove cut material when 

blade is moving. Wait until blade stops before 

grasping cut material.

 Blades coast after turn off.

3. 

Avoid cutting nails. Inspect for and remove all 

nails from lumber before cutting.

4. 

Place the wider portion of the saw base on 

that part of the workpiece which is solidly 

supported, not on the section that will fall off 

when the cut is made. If the workpiece is short 

or small, clamp it down. DO NOT TRY TO HOLD 

SHORT PIECES BY HAND!

► 

Fig.5

5. 

Before setting the tool down after completing a 

cut, be sure that the guard has closed and the 

blade has come to a complete stop.

6. 

Never attempt to saw with the circular saw 

held upside down in a vise. This is extremely 

dangerous and can lead to serious accidents.

► 

Fig.6

7. 

Some material contains chemicals which may 

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier 

safety data.

8. 

Do not stop the blades by lateral pressure on 

the saw blade.

9. 

Do not use any abrasive wheels.

10. 

Only use the saw blade with the diameter that 

is marked on the tool or specified in the man

-

ual.

 Use of an incorrectly sized blade may affect 

the proper guarding of the blade or guard opera

-

tion which could result in serious personal injury.

11. 

Keep blade sharp and clean.

 Gum and wood pitch 

hardened on blades slows saw and increases poten

-

tial for kickback. Keep blade clean by first removing 

it from tool, then cleaning it with gum and pitch 

remover, hot water or kerosene. Never use gasoline.

12. 

Wear a dust mask and hearing protection when 

use the tool.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.

FUNCTIONAL 

DESCRIPTION

CAUTION:

Always be sure that the tool is 

switched off and unplugged before adjusting or 

checking function on the tool.

Adjusting depth of cut

CAUTION:

After adjusting the depth of cut, 

always tighten the lever securely.

► 

Fig.7:

1.

 Lever

Loosen the lever on the depth guide and move the base 

up or down. At the desired depth of cut, secure the base 

by tightening the lever.

For cleaner, safer cuts, set cut depth so that no more 

than one blade tooth projects below workpiece. Using 

proper cut depth helps to reduce potential for danger-

ous KICKBACKS which can cause personal injury.

Bevel cutting

► 

Fig.8:

1.

 Clamping screw 

2.

 Bevel scale plate

Loosen the clamping screws. Set for the desired angle 

(0° - 45°) by tilting accordingly, then tighten the clamp

-

ing screws securely.

Sighting

► 

Fig.9:

1.

 Cutting line (0° position) 

2.

 Cutting line 

(45° position)

For straight cuts, align the 0° position on the front of the 

base with your cutting line. For 45° bevel cuts, align the 

45° position with it.

Switch action

WARNING:

Before plugging in the tool, 

always check to see that the switch trigger actu-

ates properly and returns to the "OFF" position 

when released.

► 

Fig.10:

1.

 Switch trigger 

2.

 Lock button / Lock-off 

button

For tool with lock button

To start the tool, simply pull the switch trigger. Release 

the switch trigger to stop. For continuous operation, 

pull the switch trigger, push in the lock button and then 

release the switch trigger. To stop the tool from the 

locked position, pull the trigger fully, then release it.