Makita CC301DWAE - Инструкция по эксплуатации - Страница 6

6 ENGLISH

6. 

Do not “jam” the wheel or apply excessive 

pressure. Do not attempt to make an excessive 

depth of cut.

 Overstressing the wheel increases 

the loading and susceptibility to twisting or binding 

of the wheel in the cut and the possibility of kick-

back or wheel breakage.

7. 

When wheel is binding or when interrupting 

a cut for any reason, switch off the power 

tool and hold the power tool motionless until 

the wheel comes to a complete stop. Never 

attempt to remove the wheel from the cut while 

the wheel is in motion otherwise kickback may 

occur.

 Investigate and take corrective action to 

eliminate the cause of wheel binding.

8. 

Do not restart the cutting operation in the 

workpiece. Let the wheel reach full speed and 

carefully re-enter the cut.

 The wheel may bind, 

walk up or kickback if the power tool is restarted in 

the workpiece.

9. 

Support panels or any oversized workpiece to 

minimize the risk of wheel pinching and kick-

back.

 Large workpieces tend to sag under their 

own weight. Supports must be placed under the 

workpiece near the line of cut and near the edge 

of the workpiece on both sides of the wheel.

10. 

Use extra caution when making a “pocket cut” 

into existing walls or other blind areas.

 The 

protruding wheel may cut gas or water pipes, elec-

trical wiring or objects that can cause kickback.

Additional Safety Warnings:

1. 

Before using a segmented diamond wheel, 

make sure that the diamond wheel has the 

peripheral gap between segments of 10 mm or 

less, only with a negative rake angle. 

2. 

Never attempt to cut with the tool held upside 

down in a vise. This can lead to serious acci-

dents, because it is extremely dangerous.

3. 

Some material contains chemicals which may 

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier 

safety data.

4. 

Store wheels as per manufacturer recommen-

dations. Improper storage may damage the 

wheels.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.

Important safety instructions for 

battery cartridge

1. 

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery 

charger, (2) battery, and (3) product using battery.

2. 

Do not disassemble battery cartridge.

3. 

If operating time has become excessively 

shorter, stop operating immediately. It may 

result in a risk of overheating, possible burns 

and even an explosion.

4. 

If electrolyte gets into your eyes, rinse them 

out with clear water and seek medical atten-

tion right away. It may result in loss of your 

eyesight.

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con-

ductive material.

(2) 

Avoid storing battery cartridge in a con-

tainer with other metal objects such as 

nails, coins, etc.

(3) 

Do not expose battery cartridge to water 

or rain.

A battery short can cause a large current 

flow, overheating, possible burns and even a 

breakdown.

6. 

Do not store the tool and battery cartridge in 

locations where the temperature may reach or 

exceed 50 °C (122 °F).

7. 

Do not incinerate the battery cartridge even if 

it is severely damaged or is completely worn 

out. The battery cartridge can explode in a fire.

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

The contained lithium-ion batteries are subject 

to the Dangerous Goods Legislation require-

ments. 

For commercial transports e.g. by third parties, 

forwarding agents, special requirement on pack-

aging and labeling must be observed. 

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required. 

Please also observe possibly more detailed 

national regulations. 

Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move 

around in the packaging.

11. 

Follow your local regulations relating to dis-

posal of battery.

SAVE THESE INSTRUCTIONS.

CAUTION:

Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that 

have been altered, may result in the battery bursting 

causing fires, personal injury and damage. It will 

also void the Makita warranty for the Makita tool and 

charger.

Tips for maintaining maximum 

battery life

1. 

Charge the battery cartridge before completely 

discharged. Always stop tool operation and 

charge the battery cartridge when you notice 

less tool power.

2. 

Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery 

service life.

3. 

Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let 

a hot battery cartridge cool down before 

charging it.