Makita CC301DWAE - Инструкция по эксплуатации - Страница 5

5 ENGLISH

Cordless cutter safety warnings

1. 

The guard provided with the tool must be 

securely attached to the power tool and 

positioned for maximum safety, so the least 

amount of wheel is exposed towards the oper-

ator. Position yourself and bystanders away 

from the plane of the rotating wheel. 

The guard 

helps to protect operator from broken wheel frag-

ments and accidental contact with wheel.

2. 

Use only diamond cut-off wheels for your 

power tool. 

Just because an accessory can be 

attached to your power tool, it does not assure 

safe operation.

3. 

The rated speed of the accessory must be at 

least equal to the maximum speed marked on 

the power tool. 

Accessories running faster than 

their rated speed can break and fly apart.

4. 

Wheels must be used only for recommended 

applications. For example: do not grind with 

the side of cut-off wheel.

 Abrasive cut-off wheels 

are intended for peripheral grinding, side forces 

applied to these wheels may cause them to 

shatter.

5. 

Always use undamaged wheel flanges that are 

of correct diameter for your selected wheel. 

Proper wheel flanges support the wheel thus 

reducing the possibility of wheel breakage.

6. 

The outside diameter and the thickness of your 

accessory must be within the capacity rating 

of your power tool.

 Incorrectly sized accessories 

cannot be adequately guarded or controlled.

7. 

The arbour size of wheels and flanges must 

properly fit the spindle of the power tool.

Wheels and flanges with arbour holes that do not 

match the mounting hardware of the power tool 

will run out of balance, vibrate excessively and 

may cause loss of control.

8. 

Do not use damaged wheels. Before each 

use, inspect the wheels for chips and cracks. 

If power tool or wheel is dropped, inspect for 

damage or install an undamaged wheel. After 

inspecting and installing the wheel, position 

yourself and bystanders away from the plane 

of the rotating wheel and run the power tool 

at maximum no load speed for one minute.

Damaged wheels will normally break apart during 

this test time.

9. 

Wear personal protective equipment. 

Depending on application, use face shield, 

safety goggles or safety glasses. As appropri-

ate, wear dust mask, hearing protectors, gloves 

and shop apron capable of stopping small 

abrasive or workpiece fragments. 

The eye pro-

tection must be capable of stopping flying debris 

generated by various operations. The dust mask 

or respirator must be capable of filtrating particles 

generated by your operation. Prolonged exposure 

to high intensity noise may cause hearing loss.

10. 

Keep bystanders a safe distance away from 

work area. Anyone entering the work area 

must wear personal protective equipment.

Fragments of workpiece or of a broken wheel may 

fly away and cause injury beyond immediate area 

of operation.

11. 

Hold the power tool by insulated gripping 

surfaces only, when performing an operation 

where the cutting accessory may contact hid-

den wiring.

 Cutting accessory contacting a “live” 

wire may make exposed metal parts of the power 

tool “live” and could give the operator an electric 

shock.

12. 

Position the cord clear of the spinning acces-

sory.

 If you lose control, the cord may be cut or 

snagged and your hand or arm may be pulled into 

the spinning wheel.

13. 

Never lay the power tool down until the acces-

sory has come to a complete stop. 

The spinning 

wheel may grab the surface and pull the power 

tool out of your control.

14. 

Do not run the power tool while carrying it at 

your side.

 Accidental contact with the spinning 

accessory could snag your clothing, pulling the 

accessory into your body.

15. 

Regularly clean the power tool’s air vents.

 The 

motor’s fan will draw the dust inside the housing 

and excessive accumulation of powdered metal 

may cause electrical hazards.

16. 

Do not operate the power tool near flammable 

materials.

 Sparks could ignite these materials.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged 

rotating wheel. Pinching or snagging causes rapid stall-

ing of the rotating wheel which in turn causes the uncon-

trolled power tool to be forced in the direction opposite 

of the wheel’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or 

pinched by the workpiece, the edge of the wheel that is 

entering into the pinch point can dig into the surface of 

the material causing the wheel to climb out or kick out. 

The wheel may either jump toward or away from the 

operator, depending on direction of the wheel’s move-

ment at the point of pinching. Abrasive wheels may also 

break under these conditions.

Kickback is the result of power tool misuse and/or 

incorrect operating procedures or conditions and can be 

avoided by taking proper precautions as given below.
1. 

Maintain a firm grip on the power tool and 

position your body and arm to allow you to 

resist kickback forces. Always use auxiliary 

handle, if provided, for maximum control over 

kickback or torque reaction during start-up.

The operator can control torque reactions or kick-

back forces, if proper precautions are taken.

2. 

Never place your hand near the rotating acces-

sory.

 Accessory may kickback over your hand.

3. 

Do not position your body in line with the 

rotating wheel.

 Kickback will propel the tool in 

direction opposite to the wheel’s movement at the 

point of snagging.

4. 

Use special care when working corners, sharp 

edges etc. Avoid bouncing and snagging the 

accessory.

 Corners, sharp edges or bouncing 

have a tendency to snag the rotating accessory 

and cause loss of control or kickback.

5. 

Do not attach a saw chain, woodcarving blade, 

segmented diamond wheel with a peripheral 

gap greater than 10 mm or toothed saw blade.

Such blades create frequent kickback and loss of 

control.