Bosch GKS 10,8 V-LI - Инструкция по эксплуатации - Страница 17

 English | 

17

Bosch Power Tools

1 609 92A 2CZ | (14.7.16)

Noise/Vibration Information

Sound emission values determined according to 
EN 60745-2-5.

Typically the A-weighted noise levels of the product are: 
Sound pressure level 90 dB(A); Sound power level 
101 dB(A). Uncertainty K = 3 dB.

Wear hearing protection!

Vibration total values a

h

 (triax vector sum) and uncertainty K 

determined according to EN 60745-2-5: 
Cutting wood: a

h

= 2.5 m/s

2

, K = 1.5 m/s

2

The vibration level given in this information sheet has been 
measured in accordance with a standardised test given in 
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different 
applications, with different accessories or insertion tools or is 
poorly maintained, the vibration emission may differ. This 
may significantly increase the exposure level over the total 
working period.
An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working 
period.
Identify additional safety measures to protect the operator 
from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work pat-
terns.

Assembly

Battery Charging



Use only the battery chargers listed on the accessories 
page. 

Only these battery chargers are matched to the lith-

ium-ion battery of your power tool.

Note: 

The battery supplied is partially charged. To ensure full 

capacity of the battery, completely charge the battery in the 
battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure 
does not damage the battery.

The lithium-ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.



Do not continue to press the On/Off switch after the 
machine has been automatically switched off. 

The bat-

tery can be damaged.

Observe the notes for disposal.

Removing the battery

The battery 

1

 is equipped with two locking levels that should 

prevent the battery from falling out when pushing the battery 
unlocking button 

2

 unintentionally. As long as the battery is 

inserted in the power tool, it is held in position by means of a 
spring.

To remove the battery 

1

, press the battery unlocking button 

2

and pull the battery out of the power tool toward the rear. 

Do 

not exert any force.

Battery Charge-control Indication

The three green LEDs of the battery charge-control indicator 

15

 indicate the charge condition of the battery 

1

. For safety 

reasons, it is only possible to check the status of the charge 
condition when the machine is at a standstill.

Press the On/Off switch 

4

 halfway or completely through to 

indicate the charge condition.

When no LED lights up after pressing the On/Off switch 

4

, the 

battery is defective and must be replaced.

Mounting/Replacing the Saw Blade



Before any work on the power tool, remove the battery.



When mounting the saw blade, wear protective gloves. 

Danger of injury when touching the saw blade.



Only use saw blades that correspond with the charac-
teristic data given in the operating instructions.



Do not under any circumstances use grinding discs as 
the cutting tool.

Spindle lock



Base plate dimensions

mm

167 x 88

Saw blade diameter, max.

mm

85

Saw blade diameter, min.

mm

85

Blade thickness, max. 

mm

0.7

Tooth thickness/setting, max.

mm

1.1

Tooth thickness/setting, min.

mm

1.0

Mounting bore

mm

15

Weight according to EPTA-
Procedure 01:2014

kg

1.3 – 1.6

*

Permitted ambient temperature
– during charging
– during operation

**

 and during 

storage

° C

° C

0 ... + 45

– 20 ... + 50

Recommended batteries

GBA 12V...

GBA 10.8V...

Recommended chargers

GAL 12..

AL 11..

Circular Saw

GKS 12V-26

* depending on the battery pack being used

** Limited performance at temperatures < 0 ° C

LED

Capacity

Continuous lighting 3 x green

≥

2/3

Continuous lighting 2 x green

≥

1/3

Continuous lighting 1 x green

< 1/3

Flashing light 1 x green

Reserve

OBJ_BUCH-2920-001.book  Page 17  Thursday, July 14, 2016  8:44 AM