Einhell GE-WS 18/150 Li-Solo (3425230) - Инструкция по эксплуатации - Страница 27

GB

- 27 -

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

7.2  Cleaning the inside of the container.

After use, clean the equipment and leave the con-

tainer open to dry. Note the cleaning instructions 

in the directions for use that came with the chemi-

cal in addition to these cleaning instructions.

Remove any remaining liquid from the tank 

through the container’s 

fi

 ller opening and store 

the liquid properly for subsequent use or dispose 

of it in accordance with the applicable regulations.

1.  Unscrew the tank lid (Fig. 5 / Item 6) from the 

tank.

2.  Remove the 

fi

 lling sieve (Fig. 4 / Item 7a) and 

clean it with ample water as required.

3.  Tilt the tank forwards and empty it completely.

4.  Reinsert the 

fi

 lling sieve (Fig. 4 / Item 7a) in 

the tank opening. Make sure that the seal 

(Fig. 4/Item 7b) is correctly seated.

5.  Screw the tank lid (Fig. 5 / Fig 6) back on the 

tank.

6.  Shake the pressure spray vigorously several 

times.

7.  Spray the contents onto the area just treated 

or an area reserved for this purpose.

8.  Repeat this process.

9.  The container can now be drained through 

the 

fi

 ller opening as described above.

10.  Allow the tank to dry out completely.

Before you use the tank again, re-insert the 

fi

 lling 

sieve and screw the tank lid back onto the tank.

7.3  Cleaning the intake 

fi

 lter (Fig. 15)

Clean the intake 

fi

 lter in the tank at least once a 

year, ideally after the winter break or when there 

are problems (see section 10). Proceed as fol-

lows:

1.  Empty the tank as described in 7.2.

2.  Pull the suction hose (Item 7c) with intake 

fi

 lter o

ff

  the pump connection (Item 7d).

3.  Rinse the suction hose and clean the intake 

fi

 lter (Item 7e) with a brush in clear water.

4. Re

fi

 t the suction hose (Item 7c) to the pump 

connection (Item 7d) and make sure that the 

intake 

fi

 lter extends to the bottom of the tank. 

Only then can the tank be properly emptied 

during spraying.

7.4  Cleaning the 

fi

 lter element in the handle 

(Fig. 16-17)

Clean the 

fi

 lter element in the handle at least 

once a year, ideally after the winter break or when 

there are problems (see section 10). Proceed as 

follows:

1.  Unscrew the union nut (Item 4a) from the 

handle (Item 4).

2.  Pull the 

fi

 lter (Item 4b) out of the handle (Item 

4) and clean it with a brush in clear water.

3.  Re-insert the 

fi

 lter (Item 4b).

4.  Screw the union nut (Item 4a) securely back 

onto the handle (Item 4).

7.5  Cleaning the nozzle and the adjustable 

spray head

Clean the nozzle and the adjustable spray head 

at least once a year, ideally after the winter break 

or when there are problems (see section 10). Ne-

ver blow out the nozzle or the spray head directly 

by mouth. Proceed as follows:

1.  Turn the adjustable spray head counterclock-

wise as far as it will go (Fig. 18).

2.  Clean the exposed nozzle (Fig. 19a) and the 

hole in the spray head (Fig. 19b) of residue 

using a thin wire.

3.  Flush the nozzle and spray head with clear 

water.

4.  Allow the nozzle and spray head to dry.

7.6 Maintenance

There are no parts inside the equipment which  

require additional maintenance.

7.7  Ordering replacement parts:

Please quote the following data when ordering 

replacement parts:

• 

 Type of machine

• 

 Article number of the machine

• 

 Identification number of the machine

• 

 Replacement part number of the part required

For our latest prices and information please go to 

www.Einhell-Service.com

Anl_GE_WS_18-150_Li_SPK9.indb   27

22.10.2020   08:47:07