Einhell GE-WS 18/150 Li-Solo (3425230) - Инструкция по эксплуатации - Страница 24

GB

- 24 -

The stated vibration emission levels and stated 

noise emission values can also be used to make 

an initial assessment of exposure.

Warning:

The vibration and noise emission levels may vary 

from the level speci

fi

 ed during actual use, depen-

ding on the way in which the power tool is used, 

especially the type of workpiece it is used for.

Keep the noise emissions and vibrations to a 

minimum.

• 

 Only use appliances which are in perfect wor-

king order.

• 

 Service and clean the appliance regularly.

• 

 Adapt your working style to suit the appliance.

• 

 Do not overload the appliance.

• 

 Have the appliance serviced whenever ne-

cessary.

• 

 Switch the appliance off when it is not in use.

• 

 Wear protective gloves.

Caution!

Residual risks

Even if you use this electric power tool in 

accordance with instructions, certain resi-

dual risks cannot be rules out. The following 

hazards may arise in connection with the 

equipment’s construction and layout:

1.  Lung damage if no suitable protective mask is 

used.

2.  Contact with hazardous substances. Spray 

materials can be harmful if inhaled or swal-

lowed or if allowed to come into contact with 

the skin or eyes. Follow the instructions and 

wear suitable protective equipment.

Danger!

This electric power tool generates an electro-

magnetic 

fi

 eld during operation. Under certain 

circumstances this 

fi

 eld may actively or passively 

impede medical implants.

To reduce the risk of serious or fatal injuries, we 

recommend persons with medical implants to 

consult their doctor and the manufacturer of the 

medical implant prior to using the equipment.

5. Before starting the equipment

Warning! 

Switch the equipment o

ff

  and remove the battery 

before carrying out any assembly work.

5.1  Assembling the spray tube and hose

Screw the spray tube onto the spray gun handle 

(Fig. 3).

Important!

 Always check the hose connections. 

Any leaks must be remedied immediately and the 

equipment must not be used until this has been 

done.

5.2  Fitting the harness (Fig. 3a - 3b)

Attach the fastening hooks for the harness (Item 

10c) to the container on the left and right sides 

(see also Fig. 9).

5.3  Preparing spray solution and 

fi

 lling the 

container

Switch o

ff

  the equipment and remove the battery.

Note: 

• 

 Always follow the manufacturer’s instructions 

when mixing spray solutions. Fill the tank only 

with the amount of solution you intend to use.

• 

 Observe the quantities to be used as listed by 

the manufacturer of the solution.

• 

 Spray solution must have a water-like consis-

tency.

• 

 The spray container can be filled with a maxi-

mum 15 liters of liquid.

• 

 Pesticides must only be prepared outdoors 

and never in living quarters, stables, or sto-

rage rooms for food and animal feed.

• 

 Spray solutions can be prepared in a sepa-

rate container and mixed thoroughly before 

being filled into the container of the pressure 

sprayer.

• 

 If you intend to use organic spray solutions, 

they must be filtered prior to filling the sprayer.

• 

 The solution must always be filled in through 

the filling sieve situated in the tank (Fig. 4 / 

Item 7a).

• 

 Clean the equipment immediately after each 

use. This is the only way to keep the liquid-

carrying parts clean and prevent clogging. 

Clogged components can lead to defects.

1.  Place the pressure sprayer on a level surface. 

Unscrew the tank lid (Fig. 5 / Item 6) from the 

tank. On the inside of the tank lid you will see 

measuring ranges with 5ml, 10ml and 25ml 

contents.

2.  Pour the amount of liquid (e.g. water) spe-

ci

fi

 ed by the solution manufacturer into the 

spray container. If the spray solution has not 

been prepared ready for spraying, add the 

measured quantity of concentrated additive 

and close the container carefully.

Anl_GE_WS_18-150_Li_SPK9.indb   24

22.10.2020   08:47:06