Einhell GE-WS 18/150 Li-Solo (3425230) - Инструкция по эксплуатации - Страница 25

GB

- 25 -

3.  If you have not already done so, mix the con-

centrated additive with the water (or other 

liquid) by shaking the pressure sprayer.

4.  Apply the name of the spray solution you are 

using to the spray solution tank (e.g. by me-

ans of a sticker)

5.4  Installing the battery

Note:

• 

 The equipment is supplied without batteries 

and without a charger.

• 

 The cover flap closes by itself and is held in 

position by magnets.

Open and hold the cover 

fl

 ap (Fig. 6/Item 8). Push 

the battery into the battery mount provided. Make 

sure that the pushlock button (Fig. 6/Item C) en-

gages as soon as the battery has been pushed in 

all the way. To remove the battery, proceed in the 

reverse order.

5.5  Charging the battery

1.  Take the battery pack out of the equipment. 

To do so, press the pushlock button. (Fig. 6/

Item C).

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

into the socket outlet. The green LED will then 

begin to 

fl

 ash.

3.  Insert the battery pack into the charger (Fig. 

7).

4.  In the section entitled „Charger indicator“ you 

will 

fi

 nd a table with an explanation of the LED 

indicator on the charger.

The battery pack can become a little warm during 

the charging. This is normal.

If the battery pack fails to charge, check:

• 

 whether there is voltage at the socket outlet

• 

 whether there is good contact at the charging 

contacts

If the battery pack still fails to charge, send

• 

 the  charger

• 

 and the battery pack

to our customer service center.

To ensure that items are properly packaged 

and delivered when you send them to us, 

please contact our customer service or the 

point of sale at which the equipment was 

purchased.

When shipping or disposing of batteries and 

cordless tools, always ensure that they are 

packed individually in plastic bags to prevent 

short circuits and 

fi

 res.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the performance of the device drops. 

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

5.6  Battery charge level indicator (Fig. 8)

Press the button for the battery charge level indi-

cator (Item A). The battery charge level indicator 

(Item B) shows the charge status of the battery 

using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs 

fl

 ash:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

5.7  Using the harness (Fig. 9)

Slip the harness over your shoulders and adjust 

the length of the harness so that you can work 

without fatigue. To do so, pull on the two ends of 

the harness to shorten it (Fig. 9 / Item 10a) or on 

the two harness release mechanisms to extend it 

(Fig. 9 / Item 10b).

Note: Should the fastening hooks for the harness 

(Fig. 9 / Item 10c) come o

ff

 , attach them back in 

position again as shown in Figs. 3a-3b.

6. Operation

WARNING!

Check the equipment for damage before you use 

it. Never use the equipment if it is damaged.

• 

 Check the tank for damage each time before 

and after using the equipment. 

• 

 Check the hose and all screw connections for 

damage and leaks each time before and after 

using the equipment.

Anl_GE_WS_18-150_Li_SPK9.indb   25

22.10.2020   08:47:06