Einhell GE-WS 18/150 Li-Solo (3425230) - Инструкция по эксплуатации - Страница 26

GB

- 26 -

6.1  Switching on

After inserting the battery, switch the equipment 

on by turning the On/O

ff

  switch to the “I” position 

(Fig. 10/Item 9).

6.2  Switching o

ff

Switch the equipment o

ff

  by turning the On/O

ff

switch to the “0” position (Fig. 10/Item 9).

6.3 Spraying

WARNING!

Note the attached lea

fl

 et with the safety instruc-

tions.

• 

 Do not use a very wide jet when spraying 

plants or other objects directly.

• 

 When the trigger lever on the spray gun hand-

le is pressed, recoil forces can occur sud-

denly, in the worst case scenario causing the 

spray tube to point towards the body. Always 

keep tight hold of the spray gun handle.

• 

 Perform spraying only when the tank is verti-

cal or upright.

6.3.1 Switching spraying on/o

ff

• 

 To spray, press the trigger lever on the spray 

gun handle (Fig. 11).

• 

 The spray jet will stop when you let go of the 

trigger lever.

• 

 If the trigger lever is pressed and then pushed 

forward (Fig. 12), this locks the lever. The 

equipment continues spraying until the trigger 

lever is pulled back again and released.

Notes!

1.  If the integrated pump contains too little spray 

solution or none at all, it will run after the 

pressure sprayer is switched on. Press the 

trigger lever on the spray gun handle for se-

veral seconds. The pump will 

fi

 ll up and spray 

solution will be ejected irregularly. Once the 

spray solution is ejected evenly, the pump will 

switch o

ff

  upon releasing the trigger lever and 

will switch on again upon pressing the lever.

2.  If there is too little spray solution in the spray 

solution container, the pump will suck in too 

little spray solution (see 1.) and will continue 

to run upon releasing the trigger lever. Top up 

with spray solution (see section 5.3).

3.  The suction hose is inside the tank on the 

right-hand side. To empty the tank as far as 

possible during spraying, bend slightly for-

wards and a little to the right.

6.3.2 Adjusting the spray jet

The spray jet can be adjusted on the nozzle from 

a single jet to a wide spray (

fi

 ne mist) for larger 

areas.

1.  Pause the spraying process.

2.  Turn the adjustable spray head counterclock-

wise to make the jet narrower until it is a sing-

le jet (Fig. 13/Item 1).

3.  Turn the adjustable spray head clockwise to 

make the jet wider (Fig. 13/Item 1).

6.4 Transport

Clip the spray tube to the side of the tank (Fig. 

14) or to the tank lid (Fig. 1). Take care that the 

spray head does not touch the ground. Transport 

the equipment by the tank lid or by means of the 

harness.

6.5  After use

Never leave spray solution in the tank. Follow the 

instructions in section 7.

• 

 Check the tank for damage each time before 

and after using the equipment. 

• 

 Check the hose and all screw connections for 

damage and leaks each time before and after 

using the equipment.

7. Cleaning, maintenance and 

ordering spare parts

Hazard!

Always pull out the battery pack before starting 

any cleaning work. Never use 

fl

 ammable solvents 

to clean the equipment.

• 

 Use only original replacement parts.

• 

 You must arrange for an authorized customer 

service center to carry out any maintenance 

and repair work that is not listed below.

• 

 Unless stipulated otherwise, we recommend 

that you arrange for the manufacturer to 

check the equipment every 2 years.

7.1  Cleaning (outside)

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 Clean the equipment regularly with a moist 

Anl_GE_WS_18-150_Li_SPK9.indb   26

22.10.2020   08:47:07