TESY CN 03 150 EIS W 304178 - Инструкция по эксплуатации - Страница 7

Operation and Storage Manual

7

EN

English

30°С, and OFF status is possible as well.

f. 

To store the point, shortly press the “Timer” button; 
then you are automatically transferred to the setting of 
the next point (the display again shows dAYX) and you 
can proceed with paragraph а) for the next point.

g. 

When you have stored a point in the last hour of the 
day – 23.5h, you cannot store any more points for this 
day in the current setting, and the display will show 
“FUL_” and the number of the day.

ATTENTION:

 Points of a particular day may be 

stored only in ascending order of their times.

Note: 

Before implementing paragraph 

f)

 the user can go 

back to paragraph 

а)

 to correct the three parameters of 

a point by shortly pressing the 

ON/OFF

 button, without storing 

the settings in the memory.

Adding more points in a particular day may be done 
at random, after you have stored points for other days, 
however  you need to observe the rule for ascending 
order of their times in a day.
To exit the settings mode, press continuously the 
“Timer” button and wait for 30 seconds.
Upon leaving the settings you can review the stored 
points by using the   and   buttons, provided that 
the appliance is in programming mode.

Note: 

When you turn on the appliance, it will start 

operating in the (heating or programming) mode which 

it has last operated.

Note: 

You can switch between the modes of operation 

(heating or programming) by shortly pressing the 

“

Timer

” button when the appliance is switched on.

“Return to factory settings” function

When the convector is in “Off ” mode, press the   and 

 buttons simultaneously for six seconds; then the 

display will show „_ _ __“ and rotating symbols. When 
it is “reset”, the display will show the measured value of 
the room temperature.
After using the reset function, you need to re-enter the 
settings of the following functions:

 •

time setting

 •

enter a value of the temperature correction (if needed)

 •

disable the “Anti-frost” function (if needed)

 •

disable the “Adaptive start” (if needed)

 •

weekly programme - 24/7

If the electric convector is disconnected from the 
mains, this will not affect the set temperature and the 
mode of operation which has been active prior to its 
disconnection. If for example the convector has been 
in “Heating” mode, after it has been disconnected and 
reconnected to the mains, it will continue operating in 
the same mode with the same set temperature.

The principle of operation of the electric 
convector with energy-independent memory is to 

store the settings for 90 minutes guaranteed, and up to 
150 minutes not guaranteed.

When the room temperature is lower than the 
temperature set by the electronic thermoregulator, 
the convector will start operating and will continue 
operating until the room temperature reaches the set 
value. When the room temperature is higher than the 
temperature set by the electronic thermoregulator, the 
convector will automatically go into “Standby” mode.

Information presented on panel heater display

Indications when you are not in settings mode:

a. 

In Off mode – consecutively showing: 

 •

time (hour and minutes)

 •

measured room temperature 

b. 

In Heating mode – it shows the measured room 
temperature 

c. 

In Programming mode – consecutively showing:

 •

Day of the week, low line and the measured 
temperature. 6_22

 •

Day of the week, low line and the temperature set in 
the programme blinking (set for the current hour), 
which may be also the OFF symbol.  6_23

d. 

Upon connecting the convector to power supply the 
display shows:

 •

Hyphens “----“, if the appliance has been in Off mode 
before disconnecting it from the power supply. 

 •

Hyphens “----“, which in 2 seconds will be 
replaced by the value of the current temperature, 
if the appliance has been in On mode before 
disconnecting it from the power supply.

e. 

Two numerals (01÷96) and a blinking yellow LED 
indicate the remaining time in hours until the delayed 
start, if the appliance has been in “Delayed start” 
mode before disconnecting it from the power supply.

f. 

With the purpose of further energy saving, the 
electronic thermoregulator reduces the brightness 
of illumination of all LEDs. Upon pressing any of the 
buttons the brightness increases for 8 seconds and it is 
then reduced again.

g. 

If the display shows “t0” or “t1“, this means that the 
self-diagnostic system has found a problem with the 
temperature sensor. “t0” indicates a disconnected 
cable at the sensor, while “t1” indicates short circuit 
at the sensor. In this case the electric convector will 
be automatically switched off and it can be switched 
on again only after the problem has been fixed. The 
problem has to be handled by a qualified specialist.

h. 

Upon switching on the power supply the display 
will show hyphens “----“ for 2 seconds instead of 
temperature of time.