IPC Portotecnica HPS DS2015T 44520 IDAC - Инструкция по эксплуатации - Страница 23

English

- 23 -

STOPPING THE CLEANER

1

)  Switch  off  the  burner  by 

turning the pressure regulator 

to pos. "0" (fig. 6B).

2

) Let the cleaner run with cold 

water only  for at least 30 se-

conds to cool down the boiler. 

3

) After using with detergent, 

flush  out  the  intake  circuit; 

place the detergent suction 

hose (fig. 8) in a tank of clean 

water and let the pump run for 

1 minute with the dosing tap 

turned fully on and the lance in 

detergent delivery condition.

4

) Stop the cleaner by turning 

the selector switch to pos. "0" 

(fig. 6A).

5

) Discharge the pressure 

from the H.P. hose by pressing 

the trigger on the gun (fig. 5A).

6

) 

Disconnect the water cle-

aner from the mains electri-

city supply via the omnipolar 

switch or by unplugging the 

plug from the socket.

7

)  Turn  off  the  water  supply 

tap (fig. 4A).

Warning

- If the water cleaner is left, 

even temporarily, turn it off by 

using the omnipolar switch or 

by unplugging the plug from 

the socket.

- Water cleaners with the “Total 

Stop” device should be con-

FIG. 6

FIG. 7

USING 

THE CLEANER 

CONTROL PANEL

A

 - On/off switch

B

 - Temperature regulator 

C

 - Detergent control tap (if 

available).

D

 - Light indicating connection  

to the mains/microleakages  (if 

available).

E

 - Burner ligth  (if available).

F

 - Light indicating diesel oil 

lack  (if available).

G

 - 

No descaler indicator light (if available).

STARTING THE CLEANER 

1

) Turn on the water supply tap (fig. 4A).

2

) Connect the water cleaner to the mains electricity supply via 

the omnipolar switch or by plugging the plug into the socket.

3

) Start the cleaner by turning the selector switch to pos. 1 

(fig. 6A).

Warning

The high pressure water jet generates a reaction force in the 

lance. Keep a firm grip on the lance handle.

4

) Press the trigger on the gun and begin washing.

5

) To use the cleaner with hot water, turn the temperature regu-

lator (fig. 6B) to the recommended washing values.

For  some  models  turn  the  ignition  switch  (fig.  6A)  onto  the 

hot  water  position  before  effecting  the  operations  described 

in this point.

Warning

In water cleaners with the “Total Stop” system, the motor starts 

and stops when the lever on the lance handle is actioned or 

released.

Danger

Do not block the handle lever in the delivery position.

IMPORTANT

!

To  eliminate  any  impurities 

or air bubbles from the wa-

ter circuit we advise starting 

the cleaner for the first time 

without the lance and letting 

the  water  run  out  for  a  few 

seconds.

Impurities  could  block  the 

nozzle and cause malfunc-

tion (Fig. 7). 

USING THE ACCESSORIES.

The high pressure washer has a nozzle with a flat  angle jet for 

cleaning large surfaces.

ROTARY HEAD (optional accessory)

The high pressure washer can be fitted with a head with rotary 

nozzle to clean the most stubborn dirt.

Danger:

Aim the jet from a certain distance to avoid damage caused by 

the high pressure. 

Do not aim the jet at people, animals or electrical sockets.

USE OF THE DOUBLE LANCE  (fig. 9)

The double lance allows the operator to select a low or high 

pressure jet.  The pressure is selected with the gun in pos. 1.  

High pressure: pos. 2.  Low pressure pos. 3.

!

!

!

!

!

FIG. 9

FIG.10

FIG. 8