Bosch AQT 42-13 0.600.8A7.300 - Инструкция по эксплуатации - Страница 17

 English | 

17

Bosch Power Tools

F 016 L81 056 | (11.4.14)

Operation

Starting

Attach water supply hose (not supplied) to the mains water 
supply and machine.

Connect the product to the mains supply ensuring that the 
mains switch is in the off position.

Open water tap.

Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
stant flow of water to clear the air from the machine and water 
supply hose. Release trigger. Press the safety lock (front but-
ton on the gun handle).

Turn button on main switch. Point the power gun downwards. 
Press the trigger safety lock to release the trigger. Fully press 
the trigger.

Autostop function

The machine is designed to switch off the motor when the trig-
ger is released on the gun.

Working Advice

General

Ensure that the pressure washer is on level ground.

Do not overreach with the high pressure hose or move the 
pressure washer by pulling the hose, this could cause the ma-
chine to become unstable and fall over.

Do not kink or drive a motor vehicle over the high pressure 
hose. Do not expose the high pressure hose to sharp edges or 
corners.

Never use a roto nozzle to clean motor vehicles.

WARNING! 

The Patio Cleaners supplied are only intended to 

be used on flat surfaces! Do not attempt to use them on steps 
or vertical surfaces. Never attempt to touch the rotating noz-
zle while operating the machine!

Working advice for cleaning with detergents



Only use cleaning agents suitable specifically for high 
pressure washers.

We recommend that you use detergent sparingly for the sake 
of the environment. Observe the recommended dilution on 
the detergent label.

The high-pressure foam nozzle supplied with this product in-
cludes a regulator to control detergent use. Adjust as re-
quired.

Recommended cleaning method

Step 1: Loosening dirt

Attach the High Pressure Foam nozzle and spray on the deter-
gent sparingly. 

Step 2: Removing dirt

Spray off the loosened dirt with the high-pressure spray.

Note: 

When cleaning a vertical surface spray off dirt/deter-

gent from the bottom and work in an upwards direction. Rinse 
from the top and work downwards.

Use with alternative water sources

This high-pressure washer is self prime and can draw water 
from water tanks and natural water sources. It’s 

IMPORTANT

that the water is clean and the BOSCH inlet filter is clear and 
fitted to the machine. 

Open tanks/containers and natural water sources 

Use the Self Priming accessory kit comprising:
– Inlet strainer with non return valve

– 3 m  reinforced  supply  hose

– Universal coupling to the pressure washer

This enables the pressure washer to draw water up to 0.5 m 
above the water level in the source in approximately 15 sec-
onds. 

Submerge the 3 m hose in water to displace the air. Connect 
the 3 m supply hose to the pressure washer ensuring that the 
inlet strainer remains submerged in the water source.

Run the pressure washer with the gun disconnected until a 
steady flow of water appears from the high pressure hose. 
Stop if this has this has not been achieved within 25 seconds 
and check all the connections. Switch off and connect the 
gun, lance and nozzle to operate. 

It is important to ensure that all hose and coupling connec-
tions are of good quality, air tight and that all washers are in 
good condition and correctly seated in place. Failure to do so 
may affect the self priming performance.

Water Tanks with outlet connections

When connecting the pressure washer to a water tank with a 
suitable tap outlet, first connect the supply hose (not provid-
ed) to the tank outlet, open the tap to allow the water to dis-
place all the air in the hose and then connect to the pressure 
washer.

OBJ_BUCH-2164-001.book  Page 17  Friday, April 11, 2014  12:41 PM