Bosch AQT 42-13 0.600.8A7.300 - Инструкция по эксплуатации - Страница 16

16

 | English 

F 016 L81 056 | (11.4.14)

Bosch Power Tools

Declaration of Conformity

Equipment category: 27

Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS23,
Stowmarket, Suffolk IP14 1EY, England

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
13.03.2014

Mounting and Operation

Starting

For Your Safety

Warning! Switch off, remove plug from mains 
before adjusting, cleaning or if cable is cut, 
damaged or entangled.

The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). Only use approved exten-
sion cables. Contact your Bosch Service Centre for details.

If you want to use an extension cable when operating your 
high pressure washer, only the following cable dimensions 
should be used:

– 1.5 mm

2

 – max length 20 m

– 2.5 mm

2

 – max length 50 m

Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.

If in doubt contact a qualified electrician or the nearest Bosch 
Service Centre.

WARNING! Inadequate extension cables can 
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.

Cable connections should be kept dry and off the ground.

For increased electrical safety to use a Residual Current De-
vice (RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.

If the supply cord is damaged, it must be replaced by a Bosch 
Service Centre.

For products 

not sold in GB

:

WARNING:

 For your safety, it is required that the plug at-

tached to the machine is connected with the extension cord. 
The coupling of the extension cord must be protected against 
splash water, be made of rubber or coated with rubber. The 
extension cord must be used with a cable strain relief.

To prevent damage to the appliance, do not allow it to operate 
dry.

Products sold in GB only

: Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse (ASTA 
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be 
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should 
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains sock-
et elsewhere.

3 600 ...

HA7 3..

HA7 4..

We declare under our sole responsibility that the product described under “Technical data” 
is in conformity with the following standards or standardization documents: EN 60335 ac-
cording to the provisions of the directives 2011/65/EU, 2004/108/EC, 2006/42/EC, 
2000/14/EC.
2000/14/EC: Guaranteed sound power level:
Conformity assessment procedure according to Annex V.

dB(A)

95

95

Henk Becker
Executive Vice President
Engineering

Helmut Heinzelmann
Head of Product Certification
PT/ETM9

Action

Figure

Delivery Scope

1

Adjusting the Handle

2

Connecting high pressure gun to lance

3

Connecting high pressure water supply hose/
nozzle

4

Attaching Nozzle

5

Water connection

6

Switching On and Off

7

Clean the water filter

8

Clean nozzle

9

Gun storage

10

Gun/lance/nozzle is stored in action

11

Hose into the hose holder

12

Storage

13

Selecting Accessories

14

OBJ_BUCH-2164-001.book  Page 16  Friday, April 11, 2014  12:41 PM