Bosch GST 8000E - Инструкция по эксплуатации - Страница 15

 English | 

15

Bosch Power Tools

1 609 92A 2GY | (3.6.16)

Contact Protector

The contact protector 

9

 attached to the casing prevents acci-

dental touching of the saw blade during the working proce-
dure and may not be removed.

Plunge Cutting (see figure D)



The plunge cutting procedure is only suitable for treat-
ing soft materials such as wood, plaster board or simi-
lar! Do not work metal materials with the plunge cut-
ting procedure!

Use only short saw blades for plunge cutting. Plunge cutting is 
possible only with the mitre angle set at 0 °.

Place the machine with the front edge of the base plate 

5

 on 

to the workpiece without the saw blade 

8

 touching the work-

piece and switch on. For machines with stroke rate control, 
select the maximum stroke rate. Firmly hold the machine 
against the workpiece and by tilting the machine, slowly 
plunge the saw blade into the workpiece.

When the base plate 

5

 fully lays on the workpiece, continue 

sawing along the desired cutting line.

Coolant/Lubricant

When sawing metal, coolant/lubricant should be applied 
alongside cutting line because of the material heating up.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself, pull the mains 
plug.



For safe and proper working, always keep the machine 
and ventilation slots clean.

If the replacement of the supply cord is necessary, this has to 
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.

Clean the saw blade holder regularly. For this, remove the saw 
blade from the machine and lightly tap out the machine on a 
level surface.

Heavy contamination of the machine can lead to malfunc-
tions. Therefore, do not saw materials that produce a lot of 
dust from below or overhead.



In extreme conditions, always use dust extraction as 
far as possible. Blow out ventilation slots frequently 
and install a portable residual current device (PRCD). 

When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power 
tool can be impaired.

Lubricate the guide roller 

7

 occasionally with a drop of oil.

Check the guide roller 

7

 regularly. If worn, it must be replaced 

through an authorised Bosch after-sales service agent.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

In all correspondence and spare parts orders, please always 
include the 10-digit article number given on the nameplate of 
the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange 
the collection of a product in need of servicing or repair. 
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au

Republic of South Africa
Customer service

Hotline: (011) 6519600

Gauteng – BSC Service Centre

35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za

KZN – BSC Service Centre

Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: bsc.dur@za.bosch.com

OBJ_BUCH-2402-003.book  Page 15  Friday, June 3, 2016  9:19 AM