Bosch GST 8000E - Инструкция по эксплуатации - Страница 12

12

 | English 

1 609 92A 2GY | (3.6.16)

Bosch Power Tools



Do not use the power tool if the switch does not turn it 
on and off. 

Any power tool that cannot be controlled with 

the switch is dangerous and must be repaired.



Disconnect the plug from the power source and/or the 
battery pack from the power tool before making any 
adjustments, changing accessories, or storing power 
tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.



Store idle power tools out of the reach of children and 
do not allow persons unfamiliar with the power tool or 
these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.



Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other 
condition that may affect the power tool’s operation. If 
damaged, have the power tool repaired before use. 

Many accidents are caused by poorly maintained power 
tools.



Keep cutting tools sharp and clean. 

Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 
and are easier to control.



Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account 
the working conditions and the work to be performed. 

Use of the power tool for operations different from those 
intended could result in a hazardous situation.

Service



Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. 

This will en-

sure that the safety of the power tool is maintained.

Safety Warnings for Jigsaws



Hold power tool by insulated gripping surfaces, when 
performing an operation where the cutting accessory 
may contact hidden wiring or its own cord. 

Cutting ac-

cessory contacting a “live” wire may make exposed metal 
parts of the power tool “live” and could give the operator an 
electric shock.



Keep hands away from the sawing range. Do not reach 
under the workpiece. 

Contact with the saw blade can 

lead to injuries.



Apply the machine to the workpiece only when 
switched on. 

Otherwise there is danger of kickback when 

the cutting tool jams in the workpiece.



Pay attention that the base plate 5 rests securely on 
the material while sawing. 

A jammed saw blade can 

break or lead to kickback.



When the cut is completed, switch off the machine and 
then pull the saw blade out of the cut only after it has 
come to a standstill. 

In this manner you can avoid kick-

back and can place down the machine securely.



Use only undamaged saw blades that are in perfect con-
dition. 

Bent or dull saw blades can break, negatively influ-

ence the cut, or lead to kickback.



Do not brake the saw blade to a stop by applying side 
pressure after switching off. 

The saw blade can be dam-

aged, break or cause kickback.



Use suitable detectors to determine if utility lines are 
hidden in the work area or call the local utility company 
for assistance. 

Contact with electric lines can lead to fire 

and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or 
may cause an electric shock.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



Always wait until the machine has come to a complete 
stop before placing it down. 

The tool insert can jam and 

lead to loss of control over the power tool.



Products sold in GB only:

 Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse 
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should 
be cut off and an appropriate plug fitted in its place by an 
authorised customer service agent. The replacement plug 
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains 
socket elsewhere.

Products sold in AUS and NZ only:

 Use a residual current 

device (RCD) with a rated residual current of 30 mA or 
less.

Product Description and 
Specifications

Read all safety warnings and all instruc-
tions. 

Failure to follow the warnings and in-

structions may result in electric shock, fire 
and/or serious injury.

While reading the operating instructions, unfold the graphics 
page for the machine and leave it open.

Intended Use

The machine is intended for making separating cuts and cut-
outs in wood, plastic, metal, ceramic plates and rubber while 
resting firmly on the workpiece. It is suitable for straight and 
curved cuts with mitre angles to 45 °. The saw blade recom-
mendations are to be observed.

Product Features

The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.

1

Lock-on button for On/Off switch

2

Thumbwheel for stroke rate preselection

3

On/Off switch

4

Hex key

5

Base plate

6

Adjusting lever for orbital action

7

Guide roller

8

Saw blade *

9

Contact protector

10

Handle (insulated gripping surface)

11

Stroke rod

OBJ_BUCH-2402-003.book  Page 12  Friday, June 3, 2016  9:19 AM