Toshiba RAS-07 - Инструкция по эксплуатации - Страница 6

 Firstly, turn off the circuit breaker.

Indoor Unit and Remote Control

●

Clean the indoor unit and the remote control with a wet cloth when 
needed.

●

No benzine, thinner, polishing powder or chemically-treated duster.

Air 

fi

 lters

Clean every 2 weeks.

1. Open the air inlet grille.
2. Remove the air 

fi

 lters.

3. Vacuum or wash and then dry them.
4. Reinstall the air 

fi

 lters and close the air inlet grille.

MAINTENANCE

22

The unit does not operate.

Cooling or Heating is abnormally low.

●

The power main switch is 
turned off.

●

The circuit breaker is 
activated to cut off the power 
supply.

●

Stoppage of electric current

●

ON timer is set.

●

The 

fi

 lters are blocked with dust.

●

The temperature has been set 
improperly.

●

The windows or doors are opened.

●

The air inlet or outlet of the outdoor 
unit is blocked.

●

The fan speed is too low.

●

The operation mode is FAN or DRY

●

POWER SELECTION function is 
set 75% or 50% 

(This function is 

depend on remote controller)

.

TROUBLESHOOTING (CHECK POINT)

23

OPERATION AND PERFORMANCE

21

1.  Three-minute protection feature: To prevent the unit from being activated 

for 3 minutes when suddenly restarted or switched to ON.

2.  Preheating operation: Warm up the unit for 5 minutes before the heating 

operation starts.

3.  Warm air control: When the room temperature reaches the set 

temperature, the fan speed is automatically reduced and the outdoor unit 

will stop.

4.  Automatic defrosting: Fans will stop during defrost operation.

5.  Heating capacity: Heat is absorbed from outdoors and released into 

the room. When the outdoor temperature is too low, use another 

recommended heating apparatus in combination with the air conditioner.

6.  Consideration for accumulated snow: Select the position for outdoor unit 

where it will not be subjected to snow drifts, accumulation of leaves or 

other seasonal debris.

7.  Some minor cracking sound may occur when unit operating. This is 

normal because the cracking sound may be caused by expansion/

contraction of plastic.

Note:

 Item 2 to 6 for Heating model

Air conditioner operating conditions

Temp.

Operation

Outdoor Temperature

Room Temperature

Heating

–15°C ~ 24°C

Less than 28°C

Cooling

–15°C ~ 46°C

21°C ~ 32°C

Dry

–15°C ~ 46°C

17°C ~ 32°C

TEMPORARY OPERATION

19

In case of the misplaced or discharged remote control

●

Pressing the RESET button, the unit can start or 
stop without using the remote control.

●

 Operation mode is set on AUTOMATIC operation, 
preset temperature is 24°C and fan operation is 
automatic speed.

How to set WEEKLY TIMER

1.   Press 

 to enter WEEKLY TIMER setting.

2.   Press 

 to select desired day in sequence.

The sequence of day symbol appears on the LCD.

SU 

t

 MO 

t

 TU 

t

 WE 

t

 TH 

t

 FR 

t

 SA

WEEKLY SUMO

TUWETHFRSA

(All day)

3.   Press 

 to select the program number.

●

The program 1 is ready for setting while 

 is 

pressed PG-1 appears on the LCD.

●

Press 

 to change the program number in 

the sequence program 1 to program 4.

PG-1
PG-  2
PG-    3
PG-      4

4.   Press 

  or 

 to select the desired time.

●

The time can be set between 0:00 and 23:50 in 
10 minute intervals.

●

Press and hold the button to change setting time 
for 1 hr.

●

Only one of ON or OFF timer can be set on each 
program.

ON timer display

OFF timer display*

* OFF timer is used to stop the air conditioner only.

The display does not show Operation mode, Temperature, 
Fan speed and others.

5.   Press 

 to select desired operation.

6.   Press 

TEMP.

 or 

 to select desired temperature.

●

The temperature can be set between 17°C and 
30°C.

7.   Press 

 to select the desired fan speed.

8.  Add operations, if required.

●

Press 

 to use 8°C operation. 

(Notes: Fireplace cannot select and memorize in 
weekly function) 

●

Press 

 to use ECO operation.

●

Press 

 to use Hi POWER operation.

●

Press 

 to use Silent operation.

WEEKLY TIMER OPERATION

24

TEMP.

PRESET

Blink

REMOTE CONTROL A-B SELECTION

20

To separate using of remote control for each indoor unit in case of 2 air 
conditioners are installed nearly.

Remote Control B Setup.

1.  Press RESET button on the indoor unit to turn the air conditioner ON.
2.  Point the remote control at the indoor unit.
3.  Push and hold 

 button on the Remote Control by the tip of the 

pencil. “00” will be shown on the display. (Picture 

1

)

4. Press 

 during pushing 

. “B” will show on the display and 

“00” will disappear and the air conditioner will turn OFF. The Remote 
Control B is memorized. (Picture 

2

)

Note:

  1. Repeat above step to reset Remote Control to be A.

2. Remote Control A has not “A” display.

3. Default setting of Remote Control from factory is A.

1

2

SELF CLEANING OPERATION (COOL 
AND DRY OPERATION ONLY)

18

To protect bad smell caused by the humidity in the indoor unit.

1. If the 

 button is pressed once during “Cool” or “Dry” 

mode, the fan will continue to run for other 30 minutes, then it will turn 
off automatically. This will reduce the moisture in the indoor unit.

2.  To stop the unit immediately, press the 

 more 2 times 

within 30 seconds.

Book_OM_1126250223_EN-UA.indb   6

Book_OM_1126250223_EN-UA.indb   6

19/3/2564 BE   17:05

19/3/2564 BE   17:05