Timberk AC TIM 09H P5BU - Инструкция по эксплуатации - Страница 7

www.timberk.com • Electric air conditioner

7

You can select three functions with this button: cooling, heating and 

dehumidification.
2. Room temperature setting button (TEMP): The set temperature is 

raised by 1°C after a single press on “up” button and is lowered by 1°C 

after a single press on “down” button.
3. POWER button: pressing this button you can switch on or off the 

unit.
4. SLEEP button: after pressing this button the fan sets to low speed.
(1) Press SLEEP button, set the sleep mode. Press the button again to 

cancel the sleep mode.
(2) In the cooling mode one hour after the sleep mode is set the 

temperature automatically increases by 1°C. In two hours the 

temperature will increase by 2°C and the established mode is 

maintained for the rest of the time. In the heating mode when SLEEP 

function is activated the temperature is, on the contrary, decreased by 

2°C in 2 hours.
(3) When power supply is turned off, the sleep mode is automatically 

switched off.
(4) When the unit is turned off, settings of the sleep mode are 

automatically turned off.
5. Timer button: ON TIMER: The ON timer is used to automatically 

switch on the unit upon expiration of the set time.
(1) Press TIMER button when the unit is OFF to set the desired time.
(2) After the set time expires, the unit will be automatically switched on.
(3) Press ON/OFF button before the set time expires. Time setting will 

be canceled and the unit will be switched on.
OFF TIMER: The OFF timer is used to automatically switch off the unit 

upon expiration of the set time.
(1) Press TIMER button when the unit is ON to set the desired time.
(2) After the set time expires, the unit will be automatically switched off.
(3) Press ON/OFF button before the set time expires. Time setting will 

be canceled and the unit will be switched off.
6. Automatic fan speed button (automatic ventilation mode).
7. High speed button. High fan speed.
8. Medium speed button. Medium fan speed.
9. Low speed button. Low fan speed.

Press the timer button when the unit is not operating to set the 
desired time (buttons 3 and 4).

The unit will be automatically switched on when the set time expires.

Press POWER button before the set time expires. Time setting will 

be canceled and the unit will be switched on.

OFF timer. 

The OFF timer is used to automatically switch off the unit upon 
expiration of the set time.

Press the timer button when the unit is operating to set the desired 
time (buttons 3 and 4).

The unit will be automatically switched off when the set time expires.

Press ON/OFF button before the set time expires. Time setting will 
be canceled and the unit will be switched off.

8. SLEEP button: after pressing this button the fan sets to low 

speed.

(1) Press SLEEP button, set the sleep mode. Press the button again 

to cancel the sleep mode.

(2) In the cooling mode one hour after the sleep mode is set the 
temperature automatically increases by 1°C. In two hours the 
temperature will increase by 2°C and the established mode is 

maintained for the rest of the time. In the heating mode when SLEEP 

function is activated the temperature is, on the contrary, decreased 
by 2°C in 2 hours.

(3) When power supply is turned off, the sleep mode is automatically 
switched off.

(4) When the unit is turned off, settings of the sleep mode are 
automatically turned off.

The portable air conditioner is equipped with a protective circuit 

featuring a 3 minute compressor activation delay. It means that it takes 

3.5 minutes for the compressor to activate after the unit is switched on 

or dehumidification mode is switched to any other mode.
9. Signaling.
“E4” signal is shown on the display at the maximum water level. To 

resume operation, remove the rubber plug of the drainage hose at the 

device’s base to drain water at first. After water is drained, start the unit. 

It will go to the normal operating mode.
1. FUNC mode selection button (SET):