Black+Decker BXCO850E - Инструкция по эксплуатации - Страница 6

ENGLISH

(Original instructions)

6

the pump.

♦

Close The steam knob (R) by turning, clockwise.

Obtaining steam:

♦

The steam is used to foam milk for cappuccino, and also 

to heat other liquids.

♦

Turn the appliance on using the on/off button.

♦

The indicators of 1cup coffee button, 2cup coffee button 

and steam button flash, the machine begins preheating, 

after all indicators are solidly on, the right temperature 

is reached.

♦

For Steam, press the Steam heating button (H), with 

Steam icon flashing, and continue heating until the 

steam temperature has been reached.

♦

The Steam light will illuminate steady, indicating that 

the water has reached the necessary temperature for 

generating steam.

♦

Note: During operation, the indicator in the steam 

selector will cycle on and off to maintain to desired 

temperature.

♦

Place a recipient under the steam tube. 

♦

Open Steam knob (R) anticlockwise

♦

Steam only will begin to exit.

♦

When you have enough, close the steam knob (R) by 

turning clockwise and remove the recipient.

IMPORTANT

♦ When you finish doing steam, you must replace the 

water used to make steam and at the same time, recover 

the temperature (lower) to make coffee.

♦

To do this, with the steam knob open, pushing previously 

over Steam Icon to stop heating, push coffee / water 

button (G1 or G2), which will activate the pump.

♦

Put a container under the tube

♦ When water starts to flow through the steam pipe, it 

means that it has recovered the coffee temperature and 

the boiler has been filled. Now you can close Steam 

knob and to push coffee button (G) to Stop position

Autooff feature:

♦

The BLACK+DECKER machines are designed to save 

energy 

To that end, after some minutes from the last operation, 

the unit switches to energy saving mode 

To return to normal operation you should just Switch ON 

the connect button (F)

Once you have finished using the appli

-

ance:

♦

Turn the appliance off, using the on/off switch (F) for a 

few seconds

♦

Unplug the appliance to the mains.

♦

Remove the water from the water tank.

♦

Clean the appliance

CLEANING  

Basic cleaning

♦

Disconnect the appliance from the mains and let it cool 

before undertaking any cleaning task.

♦

Clean the equipment with a damp cloth with a few drops 

of washingup liquid and then dry.

♦

Do not use solvents, or products with an acid or base pH 

such as bleach, or abrasive products, for cleaning the 

appliance.

♦

Do not let water or any other liquid get into the air vents 

to avoid damage to the inner parts of the appliance.

♦

No parts of this appliance are suitable for cleaning in the 

dishwasher.

♦ After washing, dry all the parts before fitting them 

together and storing.

Cleaning the Frothing Wand

♦

CAUTION! The frothing wand, and frothing sleeve may 

be VERY HOT.

♦

It is recommended to purge and wipe the frothing wand 

after steaming milk to prevent deposits of dirt and before 

turning off the machine.

♦

To do this, pull the frothing sleeve down and clean under 

warm running water.

♦

Fill a cup with a bit of water, immerse the frothing wand 

into the water.

♦

Drain hot water through the pipe, following the instruc-

tions "Obtaining hot water".

♦

 Use a cloth to dry the frothing wand and replace the 

frothing sleeve.

♦

In case no steam comes out of the frothing wand, 

hardened milk blocks its path. Carefully use a needle to 

loosen the milk residue from the opening of the frothing 

tip to remove any blockage, 

♦

Once clean, rinse with running water from the tap and 

reassemble it. Then steam again.