Siemens TK 76001 - Инструкция по эксплуатации - Страница 39

35

de

en

Dispensing hot water

r

!

Risk of burns

The milk frother 

10

 gets very hot. After use, 

allow to cool down first before touching.

The appliance must be ready for use.

Place the pre-warmed cup or glass under 
the outlet of the milk frother 

10

. 

Select the required setting for hot water 

Ê

 by turning the knob 

6

. 

Press the 

start

 button 

8

. Hot water runs 

out of the milk frother outlet 

10

 for about 

40 seconds.
Press the 

start

 button 

8

 again to cut the 

process short.

N.B.:

 It is possible to set the temperature of 

the hot water (see “Controls, °

C

 button”).

Maintenance and daily 
cleaning

r

!

   Risk of electric shock

Unplug the appliance before cleaning it.
Never immerse the appliance in water.
Do not use a steam cleaner.

Wipe the outside of the appliance with a 
damp cloth. Do not use scouring agents.
Rinse the water tank 

11

 and the brewing 

unit 

24

 with water only.

The cover of the storage compartment 

26

, the drip tray panel 

27

 and the 

insulating cover of the milk container 

34

should only be wiped gently with a damp 
cloth.  
Do not put them in the dishwasher.
Remove the grate for the coffee outlet 

29

, 

the grate for the milk frother 

31

 and the 

drip tray for the milk frother 

30

. Take out 

the drip tray for coffee outlet 

28

 with the 

coffee grounds container 

32

 by pulling 

them out forward, empty and clean. All 
these parts can also be cleaned in the 
dish washer.

●

●

●

●

●

●

●

●

Clean the measuring spoon 

14

, aroma 

cover 

16

 and the inside and cover of the 

milk container 

34

 by hand or in the dish 

washer.
Wipe out the inside of the appliance (tray 
holders).

Important: 

Drip trays 

28/30

 should be 

emptied and cleaned daily to prevent mould 
from developing.

N.B.:

 If the appliance is cold when switched 

on with the 

a

 button 

2

, or if it is set to 

a

mode after brewing coffee, it rinses 
automatically, in other words the system 
cleans itself.

Cleaning the milk system 10 

Clean the milk system 

10

 immediately after 

use!

The milk system 

10

 can be pre-cleaned 

automatically.

Select the 

Ì

 symbol in the display 

5

 and 

press the 

start

 button 

8

.

P

L ACE

EMP T Y

GL ASS

UNDER

FROTHER

, 

P

L ACE

SUCTION

PIPE

IN

GL ASS

Ò

S

TART

Place an empty glass under the milk 
system 

10

 and put the end of the pipe 

10d

 in the glass.

Press the 

start

 button 

8

. The appliance 

now fills the glass automatically with 

water and draws it in again through the 
pipe 

10d

 for cleaning. The rinse 

procedure stops automatically after about 
1 minute.
Now empty the glass and clean the pipe 

10d

.

In addition to this, clean the milk system 
thoroughly once every two weeks or so (by 
hand or in the dishwasher).

Dismantling the milk system 

10

 for 

cleaning:

Pull the milk system 

10

 forward out of the 

appliance.
Clean the individual parts (

Fig. C

) with a 

detergent solution and a soft brush.

●

●

●

●

●

●

●

●

SE_TK76_Teil_1_080917.indd   35

18.09.2008   08:40:49