Холодильник Liebherr CBNes 6256 PremiumPlus - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Activating the ice maker vacation state
Be sure the upper freezer drawer is com-
pletely closed and the ice cube bin is
installed correctly.
• Activate setup mode by touching the
Su-
perFrost
icon for 5 seconds.
• Touch the freezer compartment
Down
icon
until appears in the display.
• Touch the
SuperFrost
icon.
- The display reads
or
depending on whether the ice maker is switched
on or off.
• Touch the freezer compartment
Down
icon.
- The display reads
• Touch the
SuperFrost
icon.
- The digit flashes.
The ice cube tray rotates down.
When the interior temperature appears in the display, the tray is in
the down position and the ice maker is switched off automatically.
Switching the ice maker on
• Touch the
IceMaker icon
so that the
IceMaker LED
comes on.
After you start the ice maker for the first time, it may take up to
24 hours before the first ice cubes are ready.
The production capacity depends on the temperature inside the
freezer compartment. The lower the temperature, the more ice
cubes can be produced over a period of time.
The ice cubes fall out of the ice maker into the ice cube bin. When
the ice reaches a certain level in the bin, the appliance stops pro-
ducing ice automatically.
Switching the ice maker off
If you do not need any ice cubes, the ice maker can be switched
off independently of the freezer compartment.
• Touch the
IceMaker icon
so that the
IceMaker LED
goes out.
The ice maker can also be
switched on and off using the
ON/OFF
button at the ice maker
housing.
Press the button for approxi-
mately 1 second.
Ice maker vacation state
In case of longer vacations, the ice cube tray should be emptied.
By setting the ice maker into the
vacation state, the tray will
rotate down and no water
remains in the tray.
The freezer drawer must be
left open so that the surface
of the tray dries up and no mould
or unpleasant odours can occur.
Ice cube bin
GB
Bleeding the ice maker
To ensure that the ice maker works properly, the water supply line
must be bled.
• Touch the
IceMaker icon
so that the
IceMaker LED
comes on.
• Open the top freezer drawer.
• Press the
ON/OFF
button on the ice
maker housing for approx. 3 seconds.
The LED above the button starts flash-
ing.
• Press the button again briefly. The
LED flashes more quickly.
• Close the freezer drawer immediately.
The water supply valve opens for 25 seconds and pumps all the
air out of the water supply system.
• Then the ice cube tray of the ice maker must be completely
emptied. See the section
Activating the ice maker vacation
state
.
• Finally, clean the ice cube bin.
Ice cube bin
23
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
