Makita PLM4626N - Инструкция по эксплуатации - Страница 13

13

7-3 OPERATION PROCEDURES

During operation, tightly hold the brake handle with both 
hands.
Note: During operation, when the brake handle is 
released, the engine will stop and thus stopping the lawn 
mower from operating.

7-4 TO STOP ENGINE

CAUTION:

 The blade continues to rotate for a 

few seconds after the engine is shut off.
1. Release the brake control handle to stop the engine 

and blade.

2. Disconnect and ground the spark plug wire as 

instructed in the separate engine manual to prevent 
accidental starting while equipment is unattended.

7-5 CONNECTION FOR AUTO MOVE

For PLM4628

Grip the self-drive control handle, the lawn mower will 
move forward automatically with about 3.6 km/h

 (Fig. 9)

, 

release the self-drive handle, the lawn mower will stop 
move. 

CAUTION:

 Your mower is designed to cut normal 

residential grass of a height no more than 250 mm. 
Do not attempt to mow through unusually tall dry or wet 
grass (e.g., pasture) or piles of dry leaves. Debris may 
build up on the mower deck or contact the engine exhaust 
presenting a potential fire hazard.

7-6 FOR THE BEST RESULTS WHEN 

MOWING

Clear lawn of debris. Be sure that the lawn is clear of 
stones, sticks, wire or other foreign objects which could be 
accidentally thrown out by the mower in any direction and 
cause serious personal injury to the operator and others 
as well as damage to property and surrounding objects. 
Do not cut wet grass. For effective mowing do not cut wet 
grass because it tends to stick to the underside of the 
deck preventing proper mowing of the grass clippings. Cut 
no more than 1/3 the length of the grass. The 
recommended cut for mowing is 1/3 the length of the 
grass. Ground speed will need to be adjusted so the 
clippings can be dispersed evenly into the lawn. For 
especially heavy cutting in thick grass it may be 
necessary to use one of the slowest speeds in order to get 
a clean well mowed cut. When mowing long grass you 
may have to cut the lawn in two passes, lowering the 
blade another 1/3 of the length for the second cut and 
perhaps cutting in a different pattern than was used the 
first time. Overlapping the cut a little on each pass will 
also help to clean up any stray clippings left on the lawn. 
The mower should always be operated at full throttle to 
get the best cut and allow it to do the most effective job of 
mowing. Clean underside of deck. Be certain to clean the 
underside of the cutting deck after each use to avoid a 
build-up of grass, which would prevent proper mulching. 
Mowing leaves. The mowing of leaves can also be 
beneficial to your lawn. When mowing leaves make sure 
they are dry and are not laying too thick on the lawn. Do 

not wait for all the leaves to be off the trees before you 
mow.

WARNING:

 If you strike a foreign object, stop the 

engine. Remove wire from spark plug, thoroughly inspect 
the mower for any damage and repair the damage before 
restarting and operating the mower. Extensive vibration of 
the mower during operation is an indication of damage. 
The unit should be promptly inspected and repaired.

7-7 GRASS CATCHER

There is a window on the rear cover. You can see the 
condition of grass catcher through the window. If the 
catcher is full of grass; you will empty and clean the bag, 
make sure it is clean and ensure its meshwork is 
ventilated. 

(Fig. 10)

7-8 DECK

The underside of the mower deck should be cleaned after 
each use to prevent a buildup of grass clippings, leaves, 
dirt or other matter. If this debris is allowed to accumulate, 
it will invite rust and corrosion, and may prevent proper 
mulching. The deck may be cleaned by tilting the mower 
and scraping clean with a suitable tool (make certain the 
spark plug wire is disconnected).

7-9 HEIGHT ADJUSTMENT 

INSTRUCTIONS

CAUTION:

 Do not at any time make any 

adjustment to lawn mower without first stopping the 
engine and disconnecting the spark plug wire. 

CAUTION:

 Before changing mowing height, stop 

mower and disconnect spark plug cable.

Your mower is equipped with a central height 
adjustment lever offering 7 height positions.

1. Stop mower and disconnect spark plug cable before 

changing mower cutting height.

2. The central height adjustment lever offers you 7 

different height positions.

3. To change the height of cut, squeeze adjuster lever 

toward the wheel, moving up or down to selected 
height. 

(Fig. 11)

All wheels will be in the same height of cut.

8. MAINTENANCE 

INSTRUCTIONS

SPARK PLUG

Use only original replacement spark plug. For best 
results, replace the spark plug every 100 hours of use. 

9. LUBRICATION INSTRUCIONS

CAUTION:

 DISCONNECT SPARK PLUG 

BEFORE SERVICING.