Husqvarna LC 247Li 9676629-01 - Инструкция по эксплуатации - Страница 10

• Use this product to cut grass lawns only. It is not

permitted to use it for other tasks.

• Use personal protective equipment. See 

Personal

protective equipment on page 10.

• Do not operate the product in rain or wet conditions.

The risk of electrical shock increases if water enters

the product.

• Do not operate the product unless the blade and all

covers are attached correctly. An incorrectly

attached blade can come loose and cause personal

injury.

• Make sure that the blade does not hit objects such

as stones and roots. This can do damage to the

blade and bend the motor shaft. A bent axle causes

heavy vibration and a very high risk that the blade

becomes loose.

• If the blade hits an object or if vibrations occur, stop

the product immediately. Stop the motor, turn the

safety key to 0 and remove the battery. Examine the

product for damages. Repair damages or let an

authorised service agent do the repair.

• Never attach the motor brake handle permanently to

the handle when the motor is started.

• Put the product on a stable, flat surface and start it.

Make sure that the blade does not hit the ground or

other objects.

• Always stay behind the product when you operate it.
• Let all the wheels stay on the ground and keep 2

hands on the handle when you operate the product.

Keep your hands and feet away from the rotating

blades.

• Do not tilt the product when the motor is started.
• Be careful when you pull the product rearward.
• Never lift up the product when the motor is started. If

you must lift the product, first stop the motor, turn the

safety key to 0 and remove the battery.

• Do not walk rearward when you operate the product.
• Stop the motor when you move across areas without

grass, for example paths made of gravel, stone and

asphalt.

• Do not run with the product when the motor is

started. Always walk when you operate the product.

• Stop the motor before you change the cutting height.

Never make adjustments with the motor started.

• Never let the product stay out of view with the motor

started. Stop the motor and make sure that the

cutting equipment does not rotate.

Safety instructions for operation

Personal protective equipment

WARNING: Read the warning instructions

that follow before you use the product.

• Personal protective equipment cannot fully prevent

injury but it decreases the degree of injury if an

accident does occur. Let your dealer help you select

the right equipment.

• Use heavy-duty slip-resistant boots or shoes. Do not

use open shoes or go with bare feet.

• Use heavy, long pants.
• Use protective gloves when necessary, for example

when you attach, examine or clean the cutting

equipment.

Safety devices on the product

WARNING: Read the warning instructions

that follow before you use the product.

• Do not use a product with defective safety devices.
• Do a check of the safety devices regularly. If the

safety devices are defective, speak to your

Husqvarna service agent.

Cutting cover
• Examine the cutting cover to make sure that there

are no damages such as cracks.

Safety key
The safety key is below the battery lid. The safety key

connects the battery that supplies the motor with power.
• Start and stop the motor to do a check of the safety

key.

• If the safety key functions correctly, the motor starts

when you turn the key to 1.

(Fig. 17 )

Motor brake handle
The motor brake handle stops the motor. When the

motor brake handle is released, the motor stops.
To do a check of the motor brake, start the motor and

then release the motor brake handle. If the motor does

not stop in 3 seconds, let an approved Husqvarna

service agent adjust the motor brake.
(Fig. 18 )

To examine the start inhibitor
Do a check of the start inhibitor to make sure that it

prevents operation of the motor.
1. Pull the motor brake handle in the direction of the

handlebar. The start inhibitor stops the movement.

2. Push the start inhibitor out.(Fig. 19 )
3. Release the start inhibitor and make sure that it goes

back to its initial position.

10

429 - 002 - 13.12.2017