Metabo DSSW 360 Set 1/2 - Инструкция по эксплуатации - Страница 12

ENGLISH

en

12

coupling may fail: whiplashing hoses can cause 

serious injury as a result.
- Screw the enclosed hose connection (5) on the 

compressed air connection (4): Using an open-

end spanner, secure the compressed air connec-

tion against twisting and then screw on the hose 

connection (5) with another open-end spanner. 

See page 2, fig. A.

- Fit the enclosed double ear hose clamp onto the 

compressed air hose that you want to connect.

- Push along the compressed air hose until it meets 

the stop on the hose connection.

- Slide the double ear hose clamp onto the hose 

connection. Using a suitable pliers, pinch the two 

ears together (see Page 2, Fig. B).

6.2 Using the air tool

To benefit from the air tool's full performance, 

always use compressed air hoses with an inner 

diameter of at least 9 mm. Tool performance can be 

significantly impaired if the inner diameter is too 

small.

Caution. 

The compressed air line must not 

contain any water condensation.

Caution. 

To preserve and extend the service 

life of this tool, you must ensure that it is regu-

larly maintained with pneumatic oil lubricator. You 

can do this as follows: 
– Use oiled compressed air by fitting an oil-fog lu-

bricator. 

– Without an oil-fog lubricator: Manually apply oil 

every day via the compressed air connection. 

Use approx. 3-5 drops of pneumatic oil lubricator 

for each 10 minutes of continuous operation.

If the tool has not been in use for several days, you 

should manually apply about 5 drops of pneumatic 

oil lubricator into the compressed air connection.

Caution. 

Only allow the tool to run at idle 

speed for a brief period. 

1. Place the socket on the square  (1) attachment. 

Ensure that the accessory is fitted securely.

2. To set the direction of rotation and the torque 

on the rotation selector switch (6): 

–

 = clockwise

–

 = counter-clockwise

– 1 = low torque 
– 2 = medium torque 
– 3 = high torque 

3. Adjust the supply pressure (this is measured at 

the air outlet while the air tool is switched on). 

For details of the maximum permissible supply 

pressure, see the Chapter on "Technical Speci-

fications". 

4. Connect the air tool to the compressed air sup-

ply. 

5. To switch on: Press switch (2).

To switch off: Release switch (2)

.

Danger! 

Disconnect the compressed air con-

nection before carrying out any work.

Danger! 

Repair and maintenance work other 

than described in this section should only be 

carried out by 

qualified specialists

.

- Carry out regular maintenance to ensure the 

safety of the air tool.

- Check that all screw fittings are seated securely, 

and tighten if necessary. 

- Clean the filter in the compressed air connection 

at least once a week. 

- It is recommended that you install a pressure 

reducer with an air-water separator and lubricator 

upstream of the air tool.

- If a large amount of air or oil is escaping, check the 

air tool and have it maintained if necessary. (see 

Section 9.)

- Check the rotational speed regularly and after 

every use. Also carry out a simple check on vibra-

tion emission.

- Avoid contact with dangerous substances that 

have collected on the tool. Wear suitable personal 

protective equipment and take appropriate meas-

ures to remove any dangerous substances before 

maintenance.

f

Use only genuine Metabo accessories.
Only use accessories that are designed for this air 

tool and that fulfil the requirements and the specifi-

cations listed in these operating instructions. 
For a complete range of accessories, see 

www.metabo.com or the catalogue.

Danger! 

Repairs to air tools must only be 

carried out by qualified specialists, using orig-

inal Metabo spare parts!
If you have Metabo air tools that require repairs, 

please contact your Metabo service centre. For 

addresses see www.metabo.com.
You can download spare parts lists from 

www.metabo.com.

Observe national regulations on environmentally 

compatible disposal and on the recycling of disused 

air tools, packaging and accessories. You must not 

cause risks to people or the environment.

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
V

1

= Air requirement

p

max.

= maximum permissible supply pressure 

n

0

= Rotational speed 

F

R

7. Care And Maintenance 

8. Accessories

9. Repairs

10. Environmental Protection

11. Technical specifications