Metabo DSSW 360 Set 1/2 - Инструкция по эксплуатации - Страница 11

ENGLISH

en

11

- If you notice that the skin on your fingers or hands 

is numb, prickling or turning white, stop working 

with the air tool immediately, notify your employer 

and consult a doctor.

- The air tool must be operated in accordance with 

the recommendations provided in these instruc-

tions and must be maintained in order to avoid 

unnecessarily raising the level of vibration.

- Do not use mounts or extensions that are either 

worn or badly fitting, since this will most likely 

result in greater vibration.

- To avoid increasing the level of vibration unneces-

sarily, consumables and the accessory must be 

selected, maintained and replaced in accordance 

with these instructions.

- If possible, you should use sleeve fittings.

- To support the weight of the air tool, use a stand, 

a clamp or an equaliser whenever possible.

- Hold the air tool firmly but not too tightly using the 

required manual torque reaction: the risk of vibra-

tion is increased when the grip force is higher.

4.10 Additional safety instructions

- Compressed air can cause serious injury.

- When the air tool is not in use, before replacing 

accessory parts or when carrying out repairs, you 

must ensure that air supply is shut off, that the air 

hose is depressurised and that the air tool is 

disconnected from the compressed air supply.

- Never direct the air jet at yourself or other people.

- Hoses that whip about can cause serious injury. 

Therefore always check that the hoses and their 

fixtures are in good condition and that they have 

not become loose.

- Cold wind should be directed away from the 

hands.

- Do not use quick-lock couplings on the tool inlet. 

For threaded hose connections, only use those 

made with hardened steel (or a material with 

similar shock resistance).

- If universal swivel couplings (claw couplings) are 

being used, locking pins must also be used. You 

should also use whip check hose restraints in 

case there is a problem with the connection 

between the hose and air tool or between the 

hoses themselves. 

- Ensure that the maximum pressure specified on 

the air tool is not exceeded.

- Never carry air tools by the hose.

- Secure the air tool if it is operated in a holder. Loss 

of control can cause personal injury.

4.11 Additional Safety Instructions

- If applicable, observe any particular health and 

safety or accident prevention regulations 

governing the use of compressors and 

compressed air tools. 

- Ensure that the maximum supply pressure speci-

fied in the Technical Specifications is not 

exceeded. 

- Do not overload the tool – use it only within the 

performance range for which it was designed (see 

“Technical Specifications”). 

- Use non-hazardous lubricants. Ensure the work-

place is adequately ventilated. If there is a large 

amount of discharge: Check the air tool and have 

it repaired if necessary.

- Do not operate the tool unless you are completely 

focused. You must be alert, pay attention to what 

you are doing and proceed cautiously when 

working with an air tool. Never use a tool when you 

are tired or under the influence of drugs, alcohol or 

medication. Just one moment's carelessness 

when using the tool can cause serious injury.

- Make sure your workplace is clean and well lit. 

Untidy or poorly lit workplaces can cause acci-

dents.

- Keep air tools away from children. 

- Do not store the tool outdoors or in damp condi-

tions without protection.

- Protect the air tool, especially the compressed air 

connection and the control elements from dust 

and dirt. 

Information in these operating instructions is cate-

gorised as shown below: 

Danger! 

Risk of personal injury or environ-

mental damage. 

Caution. 

Risk of material damage

4.12  Symbols on the air tool 

Read the Operating Instructions before 

starting to use the machine.

Wear safety goggles.

Wear ear protectors.

Direction of rotation

See page 2.

1 Square attachment for sockets

2 Switch (on/off)

3 Air outlet with sound absorber

4 Compressed air connection with filter

5 Hose connection

6 Switch for setting direction of rotation and the 

torque

7 Double ear hose clamp

6.1 Before using the tool for the first time

Prepare the compressed air connection.

Danger! 

Do not fit quick-lock couplings 

directly to the compressed air connection (4). 

Never screw the enclosed connection pieces for 

quick-lock couplings directly onto the compressed 

air connection (4) - simply screw the hose 

connection (5) onto the device and then connect the 

compressed air hose to this. The compressed air 

hose between the compressed air connection (4) 

and a quick-lock coupling must be at least 20 cm in 

length. If fitted too close to the device, a quick-lock 

5. Overview

6. Operation

F

R