Bosch GDS 18 E - Инструкция по эксплуатации - Страница 9

 English | 

9

Bosch Power Tools

1 609 92A 0MM | (29.4.14)



Prevent unintentional starting. Ensure the switch is in 
the off-position before connecting to power source 
and/or battery pack, picking up or carrying the tool. 

Carrying power tools with your finger on the switch or ener-
gising power tools that have the switch on invites accidents.



Remove any adjusting key or wrench before turning 
the power tool on. 

A wrench or a key left attached to a ro-

tating part of the power tool may result in personal injury.



Do not overreach. Keep proper footing and balance at 
all times. 

This enables better control of the power tool in 

unexpected situations.



Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from 
moving parts. 

Loose clothes, jewellery or long hair can be 

caught in moving parts.



If devices are provided for the connection of dust ex-
traction and collection facilities, ensure these are con-
nected and properly used. 

Use of dust collection can re-

duce dust-related hazards.

Power tool use and care



Do not force the power tool. Use the correct power tool 
for your application. 

The correct power tool will do the 

job better and safer at the rate for which it was designed.



Do not use the power tool if the switch does not turn it 
on and off. 

Any power tool that cannot be controlled with 

the switch is dangerous and must be repaired.



Disconnect the plug from the power source and/or the 
battery pack from the power tool before making any 
adjustments, changing accessories, or storing power 
tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.



Store idle power tools out of the reach of children and 
do not allow persons unfamiliar with the power tool or 
these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.



Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other 
condition that may affect the power tool’s operation. If 
damaged, have the power tool repaired before use. 

Many accidents are caused by poorly maintained power 
tools.



Keep cutting tools sharp and clean. 

Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 
and are easier to control.



Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account 
the working conditions and the work to be performed. 

Use of the power tool for operations different from those 
intended could result in a hazardous situation.

Service



Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. 

This will en-

sure that the safety of the power tool is maintained.

Safety Warnings for Impact Wrenches



Hold power tool by insulated gripping surfaces when 
performing an operation where the cutting accessory 
or fastener may contact hidden wiring. 

Cutting accesso-

ry and fasteners contacting a “live” wire may make ex-
posed metal parts of the power tool “live” and could give 
the operator an electric shock.



Use auxiliary handle(s), if supplied with the tool. 

Loss 

of control can cause personal injury.



Hold the machine with a firm grip. 

High reaction torque 

can briefly occur while driving in and loosening screws.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



Always wait until the machine has come to a complete 
stop before placing it down. 

The tool insert can jam and 

lead to loss of control over the power tool.



Never use the machine with a damaged cable. Do not 
touch the damaged cable and pull the mains plug when 
the cable is damaged while working. 

Damaged cables in-

crease the risk of an electric shock.

Products sold in GB only

: Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse (ASTA 
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be 
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should 
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains sock-
et elsewhere.

Products sold in AUS and NZ only

: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Product Description and Specifications

Read all safety warnings and all instruc-
tions. 

Failure to follow the warnings and in-

structions may result in electric shock, fire 
and/or serious injury.

Intended Use

The machine is intended for driving in and loosening screws 
and bolts as well as for tightening and loosening nuts within 
the respective range of dimension.

Product Features

The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.

1

Tool bit *

2

Tool holder

3

Suspension hook

4

Handle (insulated gripping surface)

5

On/Off switch

6

Thumbwheel for speed preselection

7

Rotational direction switch

OBJ_DOKU-32064-002.fm  Page 9  Tuesday, April 29, 2014  1:15 PM