Bosch (0.601.9K0.020) - Инструкция по эксплуатации - Страница 14

14

 | English

Technical Data

Cordless Impact Wrench

GDS 18V-400

Article number

3 601 JK0 0..

Rated voltage

V=

18

No-load speed

A)

min

–1

0–2 500

Impact rate

A)

min

–1

0–3 700

Max. torque

A)

Nm

400

Machine screw diameter

mm

M10–M20

Tool holder

∎

 ½"

Weight according to 
EPTA-Procedure 01:2014

B)

kg

1.8–2.6

Recommended ambient tem-
perature during charging

°C

0 to +35

Permitted ambient temperat-
ure during operation and dur-
ing storage

°C

–20 to +50

Recommended rechargeable
batteries

GBA 18V...

ProCORE18V...

Recommended chargers

GAL 18...

GAX 18...

GAL 36...

A) Measured at 20–25 °C with rechargeable battery

GBA 18V 5.0Ah

.

B) Depends on battery in use

Noise/vibration information

Noise emission values determined according
to 

EN 62841-2-2

.

Typically, the A-weighted noise level of the power tool is:
Sound pressure level 

92

 dB(A); sound power

level 

103

 dB(A). Uncertainty K = 

3

 dB.

Wear hearing protection!

Vibration total values a

h

 (triax vector sum) and uncertainty K

determined according to 

EN 62841-2-2

:

Tightening screws and nuts of the maximum permitted size:
a

h

 = 

10.1

 m/s

2

, K = 

1.5

 m/s

2

The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ac-
cessories or is poorly maintained, the vibration level and
noise emission value may differ. This may significantly in-
crease the vibration and noise emissions over the total work-
ing period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.

Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and accessories, keeping their hands warm, and
organising workflows correctly.

Assembly

u

Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.

 There is risk of injury

from unintentionally pressing the on/off switch.

Charging the Battery

u

Use only the chargers listed in the technical data.

 Only

these chargers are matched to the lithium-ion battery of
your power tool.

Note: 

The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The accessory no longer rotates.

u

Do not continue to press the On/Off switch after the
power tool has automatically switched off.

 The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the Battery

The battery 

(4)

 is equipped with two locking levels to pre-

vent the battery from falling out when pushing the battery re-
lease button 

(5)

 unintentionally. As long as the battery is in-

serted in the power tool, it is held in position by means of a
spring.
To remove the battery 

(4)

, press the release button 

(5)

 and

pull the battery out of the power tool. 

Do not use force to

do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator   or 

 to

show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.

1 609 92A 878 | (12.06.2023)

Bosch Power Tools