Einhell TC-ID 720/1 E - Инструкция по эксплуатации - Страница 19

GB

- 19 -

6.6 Tips for working with your hammer drill

6.6.1 Drilling concrete and masonry

• 

Switch the Drill/Hammer drill selector switch 

(3) to position B (Hammer drill).

• 

Always use carbide drill bits and a high speed 

setting for drilling into masonry and concrete.

6.6.2 Drilling steel

• 

Switch the drill / hammer drill selector switch 

(3) to position A (drill).

• 

Always use HSS drill bits (HSS = high speed 

steel) and a low speed setting for drilling 

steel.

• 

We recommend that you lubricate the hole 

with a suitable cutting fluid to prevent unne-

cessary drill bit wear.

6.6.3 Starting holes

If you wish to drill a deep hole in a hard material 

(such as steel), we recommend that you start the 

hole with a smaller drill bit.

6.6.4 Drilling tiles

• 

To start the hole, switch the drill / hammer drill 

selector switch (3) to position A (drill).

• 

Switch the drill / hammer drill selector switch 

(3) to position B (hammer drill) as soon as the 

drill bit has passed through the tiles.

7.  Replacing the power cable

Danger!

If the power cable for this equipment is damaged, 

it must be replaced by the manufacturer or its 

after-sales service or similarly trained personnel 

to avoid danger.

8.  Cleaning, maintenance and 

ordering of spare parts

Danger!

Always pull out the mains power plug before star-

ting any cleaning work.

8.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

8.2 Carbon brushes

In case of excessive sparking, have the carbon  

brushes checked only by a quali

fi

 ed electrician.

Danger!

 The carbon brushes should not be rep 

laced by anyone but a quali

fi

 ed electrician.

8.3 Maintenance

There are no parts inside the equipment which  

require additional maintenance.

8.4 Ordering spare parts and accessories

Please provide the following information when 

ordering spare parts:

• 

Type of unit

• 

Article number of the unit

• 

ID number of the unit

• 

Spare part number of the required spare part

For our latest prices and information please go to 

www.isc-gmbh.info

Tip! For good results we 

recommend high-quality ac-

cessories from 

! 

www.kwb.eu 

welcome@kwb.eu

9.  Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw 

materials in this packaging can be reused or 

recycled. The equipment and its accessories are 

made of various types of material, such as metal 

and plastic. Never place defective equipment in 

your household refuse. The equipment should 

be taken to a suitable collection center for proper 

disposal. If you do not know the whereabouts of 

such a collection point, you should ask in your 

local council o

ffi

  ces. 

Anleitung_TC_ID_720_1_E_SPK9.indb   19

Anleitung_TC_ID_720_1_E_SPK9.indb   19

31.01.2019   14:17:09

31.01.2019   14:17:09