Einhell TC-ID 720/1 E - Инструкция по эксплуатации - Страница 18

GB

- 18 -

ches the workpiece.

5.3 Fitting the drill bit (Fig. 5)

• 

 Always pull the power plug before making ad-

justments to the equipment.

• 

  The quick-change drill chuck (1) is equipped 

with a locking fastener:

To lock = press the sleeve (a) forwards

To unlock = press the sleeve (a) backwards

• 

 Release the depth stop as described in 5.2 

and push it towards the additional handle. 

This provides free access to the chuck (1).

• 

 This hammer drill is fitted with a keyless 

chuck (1).

• 

 Open the chuck (1). The drill bit opening must 

be large enough to fit the drill bit into.

• 

 Select a suitable drill bit. Push the drill bit as 

far as possible into the chuck opening.

• 

 Close the chuck (1). Check that the drill bit is 

secure in the chuck (1).

• 

 Check at regular intervals that the drill bit or 

tool is secure (pull the mains plug).

6. Operation

 6.1 ON/OFF switch (Fig. 6/Item 5)

• 

First fit a suitable drill bit into the tool (see 

5.3).

• 

Connect the mains plug to a suitable socket.

• 

Position the drill in the position you wish to 

drill.

To switch on:

Press the ON/OFF switch (5)

Continuous operation:

Secure the ON/OFF switch (5) with the locking 

button (4).

To switch o

ff

 :

Press the ON/OFF switch (5) brie

fl

 y.

6.2 Adjusting the speed (Fig. 6/Item 5)

• 

You can infinitely vary the speed whilst using 

the tool.

• 

Select the speed by applying a greater or les-

ser pressure to the ON/OFF switch (5).

• 

Select the correct speed: The most suitable 

speed depends on the workpiece, the type of 

use and the drill bit used.

• 

Low pressure on the ON/OFF switch (5): Lo-

wer speed (suitable for: small screws and soft 

materials)

• 

Greater pressure on the ON/OFF switch (5): 

Higher speed (suitable for large/long screws 

and hard materials)

Tip:

 Start drilling holes at low speed. Then increa-

se the speed in stages.

Bene

fi

 ts:

• 

The drill bit is easier to control when starting 

the hole and will not slide away.

• 

You avoid drilling messy holes (for example 

in tiles).

6.3 Preselecting the speed (Fig. 6/Item 6)

• 

The speed setting ring (6) enables you to 

define the maximum speed. The ON/OFF 

switch (5) can only be pressed to the defined 

maximum speed setting.

• 

Set the speed using the setting ring (6) on the 

ON/OFF switch (5).

• 

Do not attempt to make this setting whilst the 

drill is in use.

6.4  Clockwise/Counter-clockwise switch 

(Fig. 6/Item 7)

• 

Change switch position only when the drill is 

at a standstill!

• 

Switch the direction of the hammer drill using 

the clockwise/counter-clockwise switch (7):

Direction  

Switch position

Clockwise (forwards and drill)   Pushed in to the 

right

Counter-clockwise (reverse)  

Pushed in to the 

left

6.5  Drill / hammer drill selector switch (Fig. 7/

Item 3)

Change switch position only when the drill is at a 

standstill!

Drill

Drill / hammer drill selector switch (3) in the drill 

position. (Position A)

Use for: Wood, metal, plastic 

Hammer drill

Drill / hammer drill selector switch (3) in the ham-

mer drill position. (Position B)

Use for: Concrete, rock, masonry

Anleitung_TC_ID_720_1_E_SPK9.indb   18

Anleitung_TC_ID_720_1_E_SPK9.indb   18

31.01.2019   14:17:09

31.01.2019   14:17:09