Bosch GSB 13 RE - Инструкция по эксплуатации - Страница 11

English | 

11

Power tool use and care

u

Do not force the power tool. Use the correct power
tool for your application. 

 The correct power tool will do

the job better and safer at the rate for which it was de-
signed.

u

Do not use the power tool if the switch does not turn it
on and off. 

 Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

u

Disconnect the plug from the power source and/or re-
move the battery pack, if detachable, from the power
tool before making any adjustments, changing ac-
cessories, or storing power tools. 

Such preventive

safety measures reduce the risk of starting the power tool
accidentally.

u

Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. 

 Power

tools are dangerous in the hands of untrained users.

u

Maintain power tools and accessories. Check for mis-
alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use.

 Many accidents are caused by

poorly maintained power tools.

u

Keep cutting tools sharp and clean. 

 Properly main-

tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.

u

Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. 

 Use of the power tool for operations different

from those intended could result in a hazardous situation.

u

Keep handles and grasping surfaces dry, clean and
free from oil and grease. 

 Slippery handles and grasping

surfaces do not allow for safe handling and control of the
tool in unexpected situations.

Service

u

Have your power tool serviced by a qualified repair
person using only identical replacement parts. 

This

will ensure that the safety of the power tool is maintained.

Safety Warnings for Drills

Safety instructions for all operations

u

Wear ear protectors when impact drilling. 

Exposure to

noise can cause hearing loss.

u

Use the auxiliary handle(s).

 Loss of control can cause

personal injury.

u

Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting ac-
cessory or fasteners may contact hidden wiring or its
own cord. 

 Cutting accessory or fasteners contacting a

"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.

Safety instructions when using long drill bits

u

Never operate at higher speed than the maximum
speed rating of the drill bit.

 At higher speeds, the bit is

likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.

u

Always start drilling at low speed and with the bit tip
in contact with the workpiece.

 At higher speeds, the bit

is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.

u

Apply pressure only in direct line with the bit and do
not apply excessive pressure.

Bits can bend causing

breakage or loss of control, resulting in personal injury.

Additional safety warnings

u

Switch the power tool off immediately if the applica-
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback.

 The applica-

tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.

u

Hold the power tool securely. 

When tightening and

loosening screws be prepared for temporarily high torque
reactions.

u

Secure the workpiece.

 A workpiece clamped with

clamping devices or in a vice is held more secure than by
hand.

u

Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility com-
pany for assistance.

 Contact with electric lines can lead

to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.

u

Always wait until the power tool has come to a com-
plete stop before placing it down.

 The application tool

can jam and cause you to lose control of the power tool.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.

Product Description and
Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.

Please observe the illustrations at the beginning of this oper-
ating manual.

Bosch Power Tools

1 609 92A 53D | (05.11.2020)