Bort BSM-1100 - Инструкция по эксплуатации - Страница 6

Hammer drill 

INTENDED USE

This tool is intended for hammer drilling in brick, concrete 
and stone as well as for drilling in wood, metal, ceramic 
and plastic. Tools with electronic speed control and left/
right rotation are also suitable for screwdriving and thread 
cutting

TECHNICAL SPECIFICATIONS 

 1 

PRODUCT ELEMENTS 

 2 

1 

On/Off switch with speed control

2 

Switch locking button

3 

Wheel for maximum speed control

4 

Switch for changing direction of rotation

5 

Switch for selecting drilling function

6 

Auxiliary handle

7 7

 Switch for selecting mechanical speed

SAFETY

WARNING!  Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, 

fi

 re 

and/or serious injury. 

●

 Wear ear protectors with hammer drills (exposure to 

noise can cause hearing loss)

●

 Use auxiliary handles supplied with the tool (loss of con-

trol can cause personal injury)

●

 Avoid damage that can be caused by screws, nails and 

other elements in your workpiece; remove them before 
you start working

●

 Always keep the cord away from moving parts of the 

tool

●

 When you put away the tool, switch off the motor and 

ensure that all moving parts have come to a complete 
standstill

●

 Use completely unrolled and safe extension cords with 

a capacity of 16 Amps (UK 13 Amps)

●

 In case of electrical or mechanical malfunction, immedi-

ately switch off the tool and disconnect the plug

●

 SBM Group can assure 

fl

 awless functioning of the tool 

only when original accessories are used

●

 Use only accessories with an allowable speed matching 

at least the highest no-load speed of the tool

●

 This tool should not be used by people under the age 

of 16 years

●

 Be careful not to drill or drive into areas where electrical 

wires may be contacted

●

 If the cord is damaged or cut through while working, do 

not touch the cord, but immediately disconnect the plug

●

 Never use tool when cord is damaged; have it replaced 

by a quali

fi

 ed person

●

 Always check that the supply voltage is the same as 

the voltage indicated on the nameplate of the tool (tools 
with a rating of 230V or 240V can also be connected to a 
220V supply)

●

 If the drill bit becomes unexpectedly jammed (causing 

a sudden, dangerous reaction), immediately switch off the 
tool

●

 Be aware of the forces that occur as a result of jamming 

(especially when drilling metals); always hold the tool 

fi

 rmly with both hands and take a secure stance

●

 Always disconnect plug from power source before mak-

ing any adjustment or changing any accessory

●

 Holding the tool 

- keep the ventilation slots uncovered
- do not apply too much pressure on the tool; let the tool 
do the work for you

Your machine is double insulated in accord-
ance with EN60745; therefore no earthwire is 
required.

MAINTENANCE

Make sure that the machine is not live when 
carrying out maintenance work on the motor. 

Regularly clean the machine housing with a soft cloth, 
preferably after each use. Keep the ventilation slots free 
from dust and dirt.If the dirt does not come off use a soft 
cloth moistened with soapy water. Never use solvents 
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please con-
tact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during 
transport, it is delivered in a sturdy packaging. Most of the 
packaging materials can be recycled. Take these materi-
als to the appropriate recycling locations. Take your un-
wanted machines to your local SBM Group dealer. Here 
they will be disposed of in an environmentally safe way.

6

English