Makita UV3600 - Инструкция по эксплуатации - Страница 6

When turning on the motor: 

Keep your feet away from the cutting tools.

Do not tilt the machine.

Do not stand in front of the discharge opening.

Never let your hands or other part of the body or 

clothing place near moving parts.

Electrical safety 

Check  the  connector  plug  on  the  machine  fits  into  the 

socket before use. 

Never modify the connector plug. 

Do not abuse the cord. Never use the cord for carrying, 

pulling  or  unplugging  the  machine.  Keep  cord  away 

from heat, oil, sharp edges or moving parts. Damaged 

or entangled cords increase the risk of electric shock.

Check the extension cable regularly for damage to the 

insulation. Replace it if damaged.

If the connecting cable is damaged, withdraw the mains 

plug immediately. A damaged cable may cause contact 

with live parts and electric shock.

Never use damaged cord.

Keep  the  cord  and  extension  cable  away  from  cutting 

tools and wheels. Cutting tools may damage the cable 

and cause electric shock.

When  using  the  machine  outdoors,  always  use  a 

residual current-operated circuit-breaker (RCD) with an 

operating current of 30 mA or less.

Use  only  extension  cable  for  outdoor  use  with  splash-

proofed  connector.  Its  cross-section  must  be  at  least 

1.mm

  for  cable  lengths  up  to  25m,  and  2.5  mm

  for 

cable lengths over 25m.

The  machine  should  be  connected  only  to  a  power 

supply  of  the  same  voltage  as  indicated  on  the 

nameplate, and can only be operated on single-phase 

AC  supply.  They  are  double-insulated  in  accordance 

with  European  Standard  and  can,  therefore,  also  be 

used from sockets without earth wire.

Avoid body contact with earthed or grounded surfaces 

(e.g. pipes, radiators, ranges, refrigerators).

Operation

Avoid operating on wet grass. Take particular attention 

when working on wet grass to prevent slipping.

Hold the handle firmly with both hands during operation. 

Keep the handle dry and clean to prevent accidents.

Do not run. Only walk during operation.

Pay  particular  attention  to  your  footings  when  working 

on a slope.

Do  not  work  straight  up  or  down  on  a  slope.  Always 

work along horizontal line.

Be  especially  careful  when  turning  the  machine  on  a 

slope.

Never work on a steep slope.

Pay  extreme  attention  when  reversing  or  pulling  the 

machine towards you.

Do not overreach. Keep proper footing and balance at 

all times. This enables better control of the machine in 

unexpected situations.

Always remember:

Keep your feet away from the cutting tools.

Do not tilt the machine.

Do not stand in front of the discharge opening.

Never let your hands or other part of the body or 

clothing place near moving parts.

Do  not  force  the  machine.  It  does  the  job  better  and 

safer  at  the  rate  for  which  it  was  designed.  Frequent 

overload may cause motor damage or fire.

•

–

–

–

–

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

–

–

–

–

•

Switch off the motor and unplug: 

Whenever leaving the machine unattended

Before clearing a blockage or any fault

Before  checking,  cleaning  or  working  on  the 

machine

Before  making  any  adjustments,  changing 

accessories or storing

When the machine hits a foreign object. Wait until 

the  machine  cools  down.  Inspect  the  machine 

and replace the parts if needed before continuing 

operation

Whenever the machine starts vibrating or making 

noise unusually

When attaching or removing grass catcher

When someone enters your working area

When crossing surface other than grass

When transporting.

Stop the cutting tool:

If you have to tilt the machine

When crossing surfaces other than grass

Transporting  the  machine  to  and  from  surfaces 

to be worked.

Pay  attention  to  the  cutting  tools.  They  do  not  stop 

immediately after switch off. 

Maintenance instructions

Have your machine serviced by our authorized service 

center,  always  using  only  genuine  replacement  parts. 

Incorrect repair and poor maintenance can shorten the 

life of the machine and increase the risk of accidents.

Inspect the machine on regular base.

Before servicing, inspection, adjustment, storage, or to 

change an accessory, take following steps:

Shut off the power source 

Disconnect the machine from power supply

Make sure that all moving parts have come to a 

complete stop

Allow the machine to cool.  

Inspect on the machine for possible damage: 

Whether  safety  devices  works  properly  for  its 

intended function

Whether all the moving parts work smoothly and 

adequately

Whether all parts are not damaged and properly 

installed

Check  the  cutting  tool  for  any  damage,  worn  or 

unbalance

Check  the  grass  catcher  regularly  for  any 

damage or worn

Check all the nuts, bolts and screws are tight

Replace  or  repair  by  our  authorized  service 

center if there are any damaged or worn parts.

Do not carry out maintenance or repair work other than 

that  described  in  this  instruction  manual.  Any  other 

work must be carried out by Makita authorized service 

center.

Only  use  original  Makita  replacement  parts  and 

accessories  intended  for  your  machine.  Otherwise 

it  may  result  in  personal  injury  or  damage  on  the 

machine.

Store the machine in a dry room. Keep it out of reach of 

children. Never store the machine outdoors.

•

–

–

–

–

–

–

–

–

–

–

•

–

–

–

•

•

•

•

–

–

–

–

•

–

–

–

–

–

–

–

•

•

•