Gorenje WHT643E4XBG - Инструкция по эксплуатации - Страница 22

22 EN

  After performing the maintenance, with the hood off and the button active, press the button for more than 3 seconds to perform the 

reset of the filter saturation indicator; repeat the operation if necessary (for ex., when both filters are saturated).

Activation of the charcoal filter saturation indicator

The saturation indicator of the charcoal filter is normally disabled. To activate it, proceed in the following manner:

With the display on (ON) and the suction off (OFF), press simultaneously the buttons 

T8

 and 

T9

 for more than 3 seconds; the button 

T9

 lights on with steady light for approx. 5 seconds, to indicate the activation.

To disable it, repeat the operation; the button 

T9

 will flash for approx. 5 seconds to indicate the disabling.

 Buttons 

T8

 and 

T9

 are not visible at this stage (on some models). They are visible only as described 

in operation section of the manual.

Approximate distance of button 

T8

 from 

T7

 is 15 mm, and distance of button 

T9

 from 

T8

 is 40 mm.

Setting of Automatic Operation parameters

For correct use of the automatic operation, perform „Hood Calibration”.

Hood Calibration

With the display on (ON) and the suction off (OFF), press button 

T3

 for 3 seconds.

The suction speed (power) 2 starts functioning and button 

T3

 flashes to indicate that hood calibration is initiated and it will last for approx. 

15 minutes.

Note:

 to interrupt the calibration, press 

T3

 for 5 seconds; the calibration will be invalidated and should therefore be repeated.

WHT943A2XBG, WHT643A2XBG, WHT663S2X, WHT963S2X

To select the functions of the hood press on the symbol. Function will be activated when symbol will be released.

T1.  Standby mode

 (the control panel off – all functions disabled) /

 ON

 (control panel switched on)

Note: 

After about a minute of inactivity (suction and lights), the hood will automatically switch to standby.

T2.  ON/OFF lights

On certain models only (see drawing above):

press repeatedly to select the desired light intensity:

L1:

 low light

L2:

 medium light

L3:

 high light

Press again to turn off the lights.

T3.  ON/OFF Automatic operation “AdaptTech”.

  The hood automatically sets the suction speed (power) 

1

 to increase if the environmental conditions detected by the hood sensor 

require it.

If there are no variations in the environmental conditions, after 10 minutes (if the hood is already in suction speed (power) 1), the hood 

turns off.

Note: 

for a correct use of this function, first perform the 

„Setting of the parameters for Automatic Operation”

 (see corresponding 

paragraph).

Note:

 During automatic operation, if the user acts on the other functions that adjust the speed, auto ventilation function is switched off.

T4.  Manual selection of the suction speed (power):

L4: 

suction speed (power) 1

L5:

 suction speed (power) 2

L6:

 suction speed (power) 3

Press again to turn off the hood (OFF).

Note: 

manual selection excludes any other suction related set function.

T5.  ON/OFF Intensive suction

 speed (power) 

“POWER BOOST”

 (timed)

Note:

 After 5 minutes of operation the hood returns to its previous state.

T6*. (Only certain models ON/OFF intensive suction speed (power) “POWER BOOST x 2”

 (timed)

Note:

 After 5 minutes of operation, the hood goes back to the previous status.

T7. ON/OFF

 operation mode 

„ReFresh”.

Every 50 minutes of inactivity, the suction speed (power 1 is turned on for 10 minutes.

T8.  ON/OFF Timer 

of the suction speed (power) (approx. 30 minutes)

Note: 

this function is available for the speeds that can be selected with button 

T4.

T9.  Indicator and reset filter saturation

The button lights on automatically with steady light when it is necessary to perform the grease filter maintenance.

The button lights on automatically with flashing light when it is necessary to perform the charcoal filter maintenance.

  After performing the maintenance, with the hood off and the button active, press the button for more than 3 seconds to perform the 

T1

T2

T3

T4

T5

T6

T7

T8

T9

L1 L2 L3

L4 L5 L6

T7

T8

T9

15 mm

40 mm