Gorenje Plus GHV92B - Инструкция по эксплуатации - Страница 38

This appliance is marked according to the 
European directive 2002/96/EC on Waste 
Electrical and Electronic Equipment (WEEE). 
By ensuring this product is disposed of 
correctly, you will help prevent potential 
negative consequences for the environment 
and human health, which could otherwise be 
caused by inappropriate waste handling of 
this product. 

The symbol 

 on the product, or on the 

documents accompanying the product, 
indicates that this appliance may not be 
treated as household waste. Instead it should 
be taken to the appropriate collection point for 
the recycling of electrical and electronic 
equipment. Disposal must be carried out in 
accordance with local environmental 
regulations for waste disposal. 
For further detailed information regarding the 
process, collection and recycling of this 
product, please contact the appropriate 
department of your local authorities or the 
local department for household waste or the 
shop where you purchased this product. 

Appliance designed, tested and manufactured 
according to: 
• Safety: EN/IEC 60335-1; EN/IEC 60335-2-
31, EN/IEC 62233. 
• Performance: EN/IEC 61591; ISO 5167-1; 
ISO 5167-3; ISO 5168; EN/IEC 60704-1; 

EN/IEC 60704-2-13; ISO 3741; EN 50564; 
IEC 62301. 
• EMC: EN 55014-1; CISPR 14-1; EN 55014-
2; CISPR 14-2; EN/IEC 61000-3-2; EN/IEC 
61000-3-3. Suggestions for a correct use in 
order to reduce the environmental impact:  
Switch ON the hood at minimum speed when 
you start cooking and kept it running for few 
minutes after cooking is finished. Increase the 
speed only in case of large amount of smoke 
and vapour and use boost speed(s) only in 
extreme situations. Replace the charcoal 
filter(s) when necessary to maintain a good 
odour reduction efficiency. Clean the grease 
filter(s) when necessary to maintain a good 
grease filter efficiency. Use the maximum 
diameter of the ducting system indicated in 
this manual to optimize efficiency and 
minimize noise. 

Additional Installation Specifications:  

Use only the fixing screws supplied with the 
product for installation or, if not supplied, 
purchase the correct screws type. 
Use the correct length for the screws which 
are identified in the Installation Guide. 
In case of doubt, consult an authorised 
service assistance centre or similar qualified 
person.

WARNING! 

Failure to install the screws or 

fixing device in accordance with these 
instructions may result in electrical hazards. 

USE

The hood is designed to be used either for 
exhausting or filter version. 

 Ducting version

In this case the fumes are conveyed outside 
of the building by means of a special pipe 
connected with the connection ring located on 
top of the hood. 

Attention

! The exhausting pipe is not 

supplied and must be purchased apart. 
Diameter of the exhausting pipe must be 
equal to that of the connection ring. 
In the horizontal runs the exhausting pipe 
must be slightly slanted (about 10°) and 
directed upwards to vent the air easily from 

the room to the outside. 
Attention! If the hood is supplied with active 
charcoal filter, then it must be removed. 

Connect the hood and discharge holes on the 
walls with a diameter equivalent to the air 
outlet (connection flange). 
Using the tubes and discharge holes on walls 
with smaller dimensions will cause a 
diminution of the suction performance and a 
drastic increase in noise. 

Any responsibility in the matter is therefore 
declined.

!

Use a duct of the minimum indispensible 
length.

!

Use a duct with as few elbows as possible 
(maximum elbow angle: 90°). 

38