Falmec LIGHT 180 - Инструкция по эксплуатации - Страница 16

16

ASSEMBLY INSTRUCTIONS

only intended for personnel qualified

The hood can be installed in various configurations.

The generic assembly steps apply to all installations; for each case, 

follow the specific steps provided for the required installation.

OPERATION

WHEN TO TURN ON THE HOOD?

Switch on the hood at least one minute before starting to cook to direct fumes 
and vapours towards the suction surface.
After cooking, leave the hood operating until complete extraction of all vapours 
and odours. By means of the Timer function, it is possible to set auto switch-off 
function which will allow the hood to turn off automatically after 15 minutes of 
operation.

WHICH SPEED IS TO BE SELECTED?

1st speed: 

maintains the circulation of clean air with low electricity consump-

tion.

2nd speed:

 normal conditions of use.

3rd speed: 

presence of strong odours and vapours.

4th speed: 

rapid disposal of odours and vapours.

WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?

The metal filters must be cleaned every 30 hours of operation. 
For further details see the “

MAINTENANCE

” chap.

ELECTRONIC PUSHBUTTON PANEL

Motor ON/OFF

Increase speed from 1 to 4

Speed 4 is only active for a few 
minutes, then speed 3 activa-
tes.

The speeds are indicated by the 
LEDs on the keys:

 Speed 1

 Speed 2

 Speed 3

 Speed 4 

("+" LED flashing)

Reduce speed from 4 to 1

Light on/off

TIMER

 (red LED flashing)

Auto switch-off after 15 min.
The function deactivates (red LED off ) if:
- The TIMER key ( ) is pressed again.
- The ON/OFF key ( ) is pressed.

If the pushbutton panel is completely inactive, before contacting 

the Technical assistance service, disconnect power temporarily 

to the appliance (about 5“), possibly by acting on the main 

switch, to restore normal operation.

If this measure has no effect, contact the Technical assistance service.

USING THE RADIO CONTROL

WARNINGS!:

Place the hood away from sources of electromagnetic waves (e.g. 

microwave ovens), which could interfere with the radio control 

and with the hood electronics.

The maximum operating distance is 5 metres, that may vary according to 

the presence of electromagnetic interferences. 

Radio control operated at 433.92MHz.

The radio control consists of two parts:

- the receiver built into the hood;

- the transmitter shown here in the figure.

DESCRIPTION OF TRANSMITTING COMMANDS

UP

Motor switch-on and speed increase 
from 1 to 4. Speed 4 is only active for a 
few minutes.

DOWN

Speed decrease and motor switch-off.

Light ON-OFF

TIMER ON

: The motor automatically 

switches off after 15 min.
The function is automatically disabled if 
the motor is switched off (

 key)

Command transmission active

RADIO CONTROL CODE CHANGE

With only one radio control, go directly to point 2.
With several radio controls in the same room, a new code can be created by fol-
lowing the procedure below.

Disconnect the power to the hood before starting the procedure.

1) - CREATE A NEW CODE

The procedure is to be carried out on the radio control.
•  Press LIGHT 

 and TIMER 

 simultaneously until the display starts flashing.

•  Press DOWN 

 on the radio control: saving is confirmed by three brief 

flashes of the display. The new code cancels and replaces the previous default 
code. 

Reconnect the hood to the electrical power supply, making sure 

that the lights and motor are off. 

2) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD

        USING THE ELECTRONIC PUSHBUTTON PANEL

press TIMER (

) 

on the hood pushbutton panel

 for 2 seconds:

the red LED lights up. 
press any key on the radio control within 10 seconds. 

RESTORING DEFAULT CODE

the procedure is to be carried out if the hood is disposed of, sold or transferred.

Disconnect the power to the hood before starting the procedure.

•

  Press UP 

 and DOWN 

 simultaneously on the radio control for more 

than 5 seconds: reset is confirmed by three brief flashes of the display. 

•  Reconnect the hood to the electrical power supply.
•  Proceed with associating the hood and the radio control, as described in point 

2.