Falmec BUILT-IN BURANO 70 BK - Инструкция по эксплуатации - Страница 15

15

ENGLISH

•  the minimum required length to avoid vibrations and reduce the suction per-

formance of the hood.

  You are required to insulate the pipes if it passes through cold environments.
  In the presence of motors with 800m3/h or higher, a check valve is present to 

prevent external air flowing back.

Deviation for Germany:
when the kitchen hood is used at the same time as appliances that are powered by 
energy other than electricity, the negative pressure in the room must not exceed 4 Pa 
(4 x 10-5 bar).

HOOD WITH INTERNAL RECIRCULATION (FILTERING)

In this model, the air passes through an optional filter unit in 
the ceiling to be purified and recycled in the environment.

In this version the check valve must not be assembled: remove it if it is 
on the air outlet fitting of the motor.

ASSEMBLY INSTRUCTIONS

only intended for qualified personnel

The hood can be installed in various configurations.

The generic assembly steps apply to all installations; for each case, 

follow the specific steps provided for the required installation.

OPERATION

WHEN TO TURN ON THE HOOD?

Switch on the hood at least one minute before starting to cook to direct fumes 
and vapours towards the suction surface.
After cooking, leave the hood operating until complete extraction of all vapours 
and odours.

WHICH SPEED IS TO BE SELECTED?

1st speed: 

maintains the circulation of clean air with low electricity consump-

tion.

2nd speed: 

normal conditions of use.

3rd speed: 

presence of strong odours and vapours.

WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?

The metal filters must be cleaned every 30 hours of operation. 
For further details see the 

“MAINTENANCE”

 chap.

MECHANICAL PUSH-BUTTON

Light ON / OFF

Motor speed 1

Motor speed 2

Motor speed 3

Turn off the motor

 MAINTENANCE

Before cleaning or carrying out maintenance operations, discon-

nect the equipment by removing the plug or switching off the 

main switch.

Do not use detergents containing abrasive, acidic or corrosive substances 

or abrasive cloths.

Regular maintenance guarantees proper operation and performance over time.
Special attention is to be paid to the 

metal anti-grease filters

: frequent clean-

ing of the filters and their supports ensures that no flammable grease is accu-
mulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood 

at least once every 

15 days

 to prevent oily substances and grease from sticking to them. To clean 

the brushed stainless steel hood, the Manufacturer recommends using "Magic 
Steel" wipes.

Alternatively 

and for all the other types of surfaces

, it can be cleaned using a 

damp cloth, slightly moistened with mild, liquid detergent or denatured alcohol.
Complete cleaning by rinsing well and drying with soft cloths. 

Do not use too much moisture or water around the push button 

control panel and lighting devices in order to prevent humidity 

from reaching electronic parts.

The glass panels can only be cleaned with specific, non-corrosive or non-abra-
sive detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with these in-
structions.

CLEANING OF INTERNAL SURFACES

Do not clean electrical parts, or parts related to the motor inside 

the hood, with liquids or solvents.

For the internal metal parts, see the previous paragraph.

METAL ANTI-GREASE FILTERS

It is advised to 

frequently

 wash the metal filters (

at least once a month

) leaving 

them to soak in boiling water and cleaning solution for 1 hour, taking care not 
to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling 
them.
Washing in a dishwasher is permitted, however, it may cause the filter material to 
darken: to reduce the possibility of this problem from happening, use low-tem-
perature washes (55°C max.).
To extract and insert the metal anti-grease filters see the assembly instructions.

LIGHTING

The range hood is equipped with high efficiency, low consumption LED spot-
lights with an extremely long life-span under normal use conditions.
Should the LED spotlight need to be replaced, proceed as shown in the figure.

12V

3

1

2