Elica NUAGE SENSE DRYWALL/F/75 - Инструкция по эксплуатации - Страница 23

23 

Automatic operation (sensor), connection with SNAP

® 

and Elica hob 
Attention!

 We recommend "

Adjusting the parameters for 

automatic Operation" 

(see relative paragraph) before using 

the automatic operation and connecting the hood to 

SNAP

® 

and to the Elica hob. 
 

Automatic operation (sensor) 

The hood will switch on at an adequate speed depending on 
the cooking fumes detected by the hood sensor.

To activate this function: 
Press keys 

T1

 and 

T2

 simultaneously. LED 

L1

 will light up 

showing several colours, whereas LED 

L2

 will turn white. 

Automatic operation of the hood with SNAP

® 

Note:

SNAP

®

 is an auxiliary suction unit capable of operating 

together with the hood. For further information, refer to the 
manual supplied with 

SNAP

® 

To activate this function: 
Press keys 

T1

 and 

T2

 simultaneously. LED 

L1

 will light up 

showing several colours, whereas LED 

L2

 will turn orange.

Automatic operation of the hood with the Elica hob 

The behaviour of the hood depends on the use of the Elica 
hob. 
 
To activate this function: 
Press keys 

T1

 and 

T2

 simultaneously. LED 

L1

 will light up 

showing several colours, whereas LED 

L2

 will turn blue. 

Automatic operation of the hood with SNAP

® 

and hob 

To activate this function: 
Press keys 

T1

 and 

T2

 simultaneously. LED 

L1

 will light up 

showing several colours, whereas LED 

L2

 will turn orange.

Adjusting the parameters for automatic operation. 

Note:

 All the calibration, selection, adjustment, and 

logical connection operations described below are 
possible with 

hood OFF

 and involve: 

• 

Hood calibration (automatic or manual). 

• 

Hob selection (gas - induction or electrical) 

•  Logical connection between hood and hob (if in 

possession of an  Elica hob) 

• 

Logical connection between hood and 

SNAP

®

 (if in 

possession of 

SNAP

®

). 

Sensor calibration 
Note:

 Calibration lasts about 5 minutes. LEDs 

L1

 and

 L2

turn white and flash. 
Calibration is required to allow the hood sensor to run 
properly. Calibration can be: 

 Automatic:

every time the hood is reconnected to the mains (e.g. 
upon first installation or after a blackout). 

 Manual: 
 

To be carried out if unsatisfactory automatic operation is 
detected and under normal kitchen conditions. 

Press and hold key 

T1

.. 

 Hob 

selection 

(gas - induction or electrical)

Simultaneously press keys 

T1

 and 

T2

 until you hear a 

beep

. Release the keys and press solely 

T2

 (within about 

5 seconds) to access the hob selection mode.. 

Press T2 again to choose the required hob according to 
the layout below: 

Orange LED 2 Gas hob 

Blue LED 2: Induction hob 

White LED 2: electrical hob 

The selected key remains on to indicate the selection. 
After 10 seconds, the key flashes temporarily to indicate 
that the selection made has been recorded. 

 
Logical connection between hood and hob 

(if in 

possession of an  Elica hob). 

a.

 Connect the hood and Elica hob simultaneously. 

b.

 the hood emits two intermittent beeps to indicate 

that it is ready to receive the connection signal from 
the Elica hob. 

c.

 the attempts to connect to the Elica hob last 5 

minutes. Within this period, the hood emits 3 
consecutive beeps to indicate that the Elica hob has 
been connected successfully. 

d.

 Check the connection with the Elica hob (see 

paragraph "

Automatic operation of the hood with 

the hob"

). 

In the event the logical connection between the 
hood and Elica hob has failed, proceed as 
follows: 

Disconnect and reconnect the hood to the mains at 
least 5 times within 30 seconds. 
Repeat operations 

a-b-c-d

 described above 

Logical connection between hood and SNAP

®

 (if in 

the possession of SNAP

®

). 

The connection between hood and SNAP

® 

is 

automatic. No setting is required.