Elica HIDDEN ADVANCE BL MAT/A/52 - Инструкция по эксплуатации - Страница 8

In standard mode, the carbon filter warning is not active.

If the hood is used in the filter version, it is necessary to enable the carbon filter warning.

Carbon filter warning activation:

Switch  the  hood  OFF  and  simultaneously  press  and  hold  keys  T2  and  T3  for  3”  (if  LED  L2  flashes,  it  means  that  the
carbon filter is NOT active), press key T3 to activate the carbon filter warning function. LEDs L2 and L5 are steady, 

wait

10” after which the function is 

activated

 followed by an acoustic signal (beep).

Carbon filter warning deactivation:

Switch  the  hood  OFF  and  simultaneously  press  and  hold  keys  T2  and  T3  for  3”  (if  LED  L2  is  steady,  it  means  that  the
carbon  filter  is  active),  LEDs  L2  and  L5  are  steady,  press  key  T3  and  LED  L2  will  start  flashing, 

wait

  10”  after  which  the

carbon filter warning function is 

deactivated

 followed by an acoustic signal (beep).

 MAINTENANCE WARNINGS

• 

Cleaning:

  For  cleaning,  simply  use  a  cloth  moistened  with  neutral  liquid  detergents.  Do  not  use  cleaning  tools  or

instruments.

For product maintenance, see the images at the end of the installation marked by this symbol.

•

Anti-Grease Filter:

 The metallic anti-grease filter must be cleaned once a month with non-aggressive detergen-

ts, manually or in a dishwasher on a short wash at low temperatures. To remove the anti-grease filter, pull the spring re-
lease handle.

•

Carbon filter (for filter version only):

 The cartridge must be replaced at least every four months. It CANNOT

be washed or regenerated. As indicated in the drawings section: remove the anti-grease filters, apply a carbon filter on
each side and attach it to the product. Put the anti-grease filters back in place.

• 

Washable activated carbon filter (for filter version only):

The  carbon  filter  can  be  washed  every  two  months  (or  when  indicated  by  the  filter  saturation  system  -  if  included  in  your
model).  As  indicated  in  the  drawing  section:  remove  the  grease  filter,  remove  the  carbon  filter  and  wash  using  hot  water
and  suitable  detergents  or  in  a  dishwasher  at  65°C  (if  washing  in  a  dishwasher,  carry  out  the  complete  washing  cycle
without  dishes  inside).  Remove  any  excess  water  without  damaging  the  filter,  then  place  it  in  the  oven  for  10  minutes  at
100°C to dry it out completely. Put the anti-grease filters back in place.
Replace the foam layer every 3 years and each time the cloth appears damaged.

•

Perimeter suction panel (panel maintenance)

Disassembly:

a. firmly pull the panel (FRONT SIDE) downwards
b. release it from the rear hinges.

Cleaning: 

the suction panel must be cleaned manually using non-aggressive detergents.

Assembly: 

the panel must be hooked at the back and secured at the front (with magnets).

Attention!

 Always check that the panel is securely fixed in place.

•

Lighting system

 : The lighting system cannot be replaced by the user, contact Customer Service in case of malfunc-

tion.

END-OF-LIFE DISPOSAL

This  device  is  marked  in  compliance  with  the  European  Directive  2012/19/EC  -  UK  SI  2013  No.3113,  Waste
Electrical and Electronic Equipment (WEEE). Make sure that this product is disposed of correctly. The user helps
prevent potential negative consequences for the environment and for health.

The  symbol  on  the  product  or  accompanying  documentation  indicates  that  this  product  should  not  be  treated  as
household  waste  but  should  be  handed  over  at  a  suitable  collection  point  for  the  recycling  of  electrical  and  electronic
equipment.  Dispose  of  it  in  accordance  with  local  regulations  for  waste  disposal.  For  further  information  about  the
treatment, recovery and recycling of this product, please contact your local authority, the collection service for household
waste or the shop from where the product was purchased.

REGULATIONS

Equipment designed, tested and manufactured in compliance with safety regulations: EN/IEC 60335-1; EN/IEC 60335-2-
31,  EN/IEC  62233.  Performance:  EN/IEC  61591;  ISO  5167-1;  ISO  5167-3;  ISO  5168;  EN/IEC  60704-1;  EN/IEC
60704-2-13;EN/IEC  60704-3;  ISO  3741;  EN  50564;  IEC  62301.  EMC:  EN  55014-1;  CISPR  14-1;  EN  55014-2;  CISPR
14-2; EN/IEC 61000-3-2; EN/IEC 61000-3-3.

8