Elica HIDDEN 2.0 IX/A/72 - Инструкция по эксплуатации - Страница 20

19 

T2.   Suction speed (power) control button: 1, 2, 3, intensive 

Note:  Intensive speed lasts for about 5 minutes, then it 

is automatically set to speed 3. 

T3.  ON/OFF button (short press) and light intensity 

adjustment (long press). 

Light colour temperature adjustment: 

With the light ON, press and hold T1 + T3 to change the light 

colour temperature. 

Filter Saturation Indicator 

The hood signals when necessary to perform filter 

maintenance: 

Grease filter (every 40 hours of use):  all Leds with red light 

Activated charcoal odour filter  (every 160 hours of 

operation): all LEDs with red light, LEDs L2 and L3 blink 

Reset Filter Saturation 

After performing filter maintenance, press and hold buttons T1 

and T3, Leds L1,  L2 and L3 blink briefly in red and then turn 

off for good.  

Activation indicator for odour filter saturation with 

activated charcoal  

This indicator is normally disabled. To enable it, proceed as 

follows: 

With the hood off, press and hold simultaneously T1 and T2: 

L1  turns on first, then L2 and L3 and after that, when the 

buttons are released, the Leds L2 and L3 flash briefly to 

indicate successful activation.  

Disabling the LED for charcoal filter saturation: repeat the 

operation above; first the LEDs L1, L2 and L3 turn on 

simultaneously, then only L1, and after that, when the buttons 

are released, the leds L1, L2 and L3 turn on again to indicate 

successful disabling.   

Maintenance 

Cleaning 

Clean using ONLY a cloth dampened with neutral liquid 

detergent.  DO NOT CLEAN WITH TOOLS OR 

INSTRUMENTS. Do not use abrasive products. DO NOT USE 

ALCOHOL! 

Panel 

Fig. 9-12-13 

Maintenance of the panel 

Disassembly:  

a. pull the panel (FRONT SIDE) downwards energetically 

b. unhook it from the back hinges. 

Cleaning: 

the suction panel must be cleaned as frequently as the grease 

filter, use a dampened cloth with neutral liquid detergents.  

Avoid using products containing abrasives. DO NOT USE 

ALCOHOL! 

Assembly: 

The panel must be hooked in the back and fixed in the front 

(with magnets).  

Attention!  always check that the panel is tightly fixed to its 

place. 

Grease filter 

Fig. 9-12 

Traps cooking grease particles.  

The grease filter must be cleaned once a month using non 

aggressive detergents, either by hand or in the dishwasher, 

which must be set to a low temperature and a short cycle.  

When washed in a dishwasher, the grease filter may discolor 

slightly, but this does not affect its filtering capacity. 

To remove the grease filter, pull the spring release handle. 

Charcoal filter (filter version only) 

It absorbs unpleasant odors caused by cooking. 

Circular charcoal filter 

Apply one on each side as cover to both the shield grids of the 

motor impeller, then turn clockwise. 

For the disassembly, turn counter-clockwise. 

The activated charcoal filter can be one of these types: 

•  Washable activated charcoal filter. 

•  NON-washable activated charcoal filter. 
Washable activated charcoal filter 

Fig. 11 

The charcoal filter can be washed once every two months (or 

when the filter saturation indication system – if envisaged on 

the model in possession – indicates this necessity)   using hot 

water and a suitable detergent, or in a dishwasher at 65°C (if 

the dishwasher is used, select the full cycle function and leave 

dishes out). 

Eliminate excess water without damaging the filter, then 

remove the mattress located inside the plastic frame and put it 

in the oven for 10 minutes at 100° C to dry completely. 

Replace the mattress every 3 years and when the cloth is 

damaged. 
NON-washable activated charcoal filter 

Fig. 10 

The saturation of the charcoal filter occurs after more or less 

prolonged use, depending on the type of cooking and the 

regularity of cleaning of the grease filter. 

In any case it is necessary to replace the cartridge at least 

every four months. 

The charcoal filter may NOT be washed or regenerated. 

Replacing lamps 

The hood is equipped with a lighting system based on LED 

technology. 

The LEDs guarantee an optimum lighting, a duration up to 10 

times longer than the traditional lamps and allow to save 90% 

electrical energy. 

For replacement, contact the technical service.