Elica HIDDEN 2.0 IX/A/72 - Инструкция по эксплуатации - Страница 19

18 

WARNING!  

Before re-connecting the hood circuit to the mains supply and 

checking the efficient function, always check that the mains 

cable is correctly assembled. 

Warning!  If the supply cord is damaged, it must be replaced 

by the manufacturer, its service agent or similarly qualified 

persons in order to avoid hazard.  

Mounting 

Before beginning installation:  

•  Check that the product purchased is of a suitable size for 

the chosen installation area. 

•  Remove the charcoal (*) filter/s if supplied (see also 

relative paragraph). This/these is/are to be mounted only 

if you want lo use the hood in the filtering version. 

•  Check (for transport reasons) that there is no other 

supplied material inside the hood (e.g. packets with 

screws (*), guarantees (*), etc.), eventually removing 

them and keeping them. 

In the case of the presence of panels and/or walls and/or 

lateral wall units check that there is sufficient space to install 

the hood and that access to the command panel is easy. 

To remove the hood from the wall unit, perform the 

mounting steps in reverse order. 
Caution! Use suitable cut resistant gloves. 

Elica Connect 

The hood features a WiFi function for remote connection via 

the Elica Connect app.  

Minimum system requirements: 

•  2.4GHz WiFi b/g/n wireless router 

•  Android or iOs Smartphone. Via the stores, check that 

the app is compatible with the operating system your 

Smartphone is running. 

Note: The ELICA manufacturer declares that this model of 

household appliance with WiFi module radio equipment 

complies with Directive 2014/53/EU. 

The radio equipment operates within the 2.4GHz ISM 

frequency band, the maximum radio frequency power 

transmitted does not exceed 20 dBm (e.i.r.p.). 

Warnings: 

•  Data protection. The data that the connected device 

detects is collected to allow for all the services of the 

connected appliance to be used. Further information on 

how the collected data is processed and on the privacy 

policy is available at www.elica.com. 

•  Availability in different countries. The Elica Connect 

service is available in specific countries. For further 

information, see the dedicated section at www.elica.com. 

•  Future changes. Elica reserves the right to make any 

changes deemed useful to improve the Elica Connect 

service. As a result, the descriptions contained in this 

manual are not binding and should be treated as purely 

indicative. 

Operation 

 T1. WiFi button 

• WiFi configuration: if the WiFi function is not 

configured, press for about 2 seconds to enter WiFi 

configuration mode and follow the instructions on the App 

to complete the procedure.  

During the configuration procedure, the button will light 

up indicating the connectivity status (see WiFi status 

table) 

To interrupt the WiFi configuration procedure, press for 

about 2 seconds when the button is lit up and is flashing 

fast. 

Once the WiFi function has been configured, if you want 

to change it, press for about 6 seconds to reset the WiFi 

parameters (the button will turn off) and repeat the 

configuration procedure. 

• WiFi activation/deactivation: after the configuration, it 

is possible to deactivate/activate the WiFi function. Press 

for about 2 seconds to deactivate/activate the WiFi 

function. Deactivating the function does not cause the 

loss of the WiFi parameters. 

WiFi status table

WiFi button 

Device connection status 

Light off 

WiFi not configured or off 

White light on 

steady 

WiFi connected  

Orange light 

flashing fast 

Attempt to connect to the 

WiFi router 

Orange light 

flashing slowly 

Attempt to connect to the 

Elica cloud 

White light on with 

short flashing 

orange light 

Remote command being 

received (e.g. engine 

ignition or light turned on)