ELICA ADAGIO GME BL/A/90 - Инструкция по эксплуатации - Страница 18

18 

Operation anomalies

The hood does not work

Make sure that: 
• 

There is no current blackout 

• 

A speed has been effectively selected. 

• 

The panel is correctly hooked. 

• 

The 9-pole connection is well inserted (

Picture 9b

). 

•  The red reset key above the electric system box is 

pressed. 

• 

The wires in the 9-pole connection are well inserted into 
the connector. (During connection, exerting an 
overpressure may cause the contacts to bend). 

The hood has low efficiency 

Make sure that: 
• 

The motor speed selected is sufficient for the quantity of 
fumes present 

• 

The kitchen is aired enough to allow an air intake and the 
charcoal filter is not worn out (filter version hood). 

• 

The air outlet pipe is not clogged. 

• 

The suction unit non-return valves can rotate freely. 

The hood stops during operation 

Make sure that: 
• 

There is no current blackout 

• 

The differential magnetothermal switch (automatic circuit 
breaker) has not been released. 

Maintenance 

Cleaning 

Clean using 

ONLY

 the cloth dampened with neutral liquid 

detergent. 

DO NOT CLEAN WITH TOOLS OR 

INSTRUMENTS

. Do not use abrasive products. 

DO NOT USE 

ALCOHOL! 

Grease filter 

Traps cooking grease particles. 

This must be cleaned once a month (or when the filter 
saturation indication system – if envisaged on the model in 
possession – indicates this necessity)  using non aggressive 
detergents, either by hand or in the dishwasher, which must 
be set to a low temperature and a short cycle. 
When washed in a dishwasher, the grease filter may discolor 
slightly, but this does not affect its filtering capacity. 
When inserting and removing grease filters and charcoal 
filters, please make sure that the extractable unit of the hood 
is in open position .In order to do this,pull the 

OFF

 (

T5

)key. 

Then remove the front panel ,by pulling on the upper part of 
each side at the same time (

Fig.13

). 

The panel turns forward ,so that grease filters can be inserted 
(

Fig.14

). 

Charcoal filter (filter version only) 

It absorbs unpleasant odors caused by cooking. 

The saturation of the 

charcoal filter

 occurs after more or less 

prolonged use, depending on the type of cooking and the 
regularity of cleaning of the grease filter. 
In any case it is necessary to replace the cartridge at least 
every four months. 
The charcoal filter may NOT be washed or regenerated. 
After removing the grease filter, it is possible to insert the 
charcoal filters (

Fig. 15

) (

not supplied

). 

Replacing lamps 

(Depending on the model available).Disconnect the appliance 
from the electricity. 

Warning! 

Prior to touching the light bulbs ensure they are 

cooled down. 
Replace the old light bulb with the one of the same type as 
specified in the feature label or near the light lamp on the 
hood. 
To replace the neon proceed as follows: 

1. 

Lift the trolley. 

2. 

Disconnect from power supply. (this operation can be 
carried out by disconnecting the plug, if accessible, or 
open the switch if envisaged during installation or press 
the red button in the control box (

Fig. 10c

) 

3. 

Remove the screws which fix the upper front as shown in 
(

Fig. 16

) 

4. 

Lift the upper front (

Fig. 17

) 

5. 

Remove the damaged neon (

Fig. 18

) and replace it with 

one having the same characteristics 

 If the lights do not work, make sure that the lamps are fitted 
properly into their housings before you call for technical 
assistance.